Manufacturing Technology 2026, 26(4):396-407 | DOI: 10.21062/mft.2026.041

Design and Analysis of High-Precision Hydraulic Press Frame for Aviation Based on Finite Element Method

Lu Dong ORCID..., Yaoming Fu ORCID..., Jie Pang ORCID..., Rui Nie ORCID..., Zehua Hua ORCID...
Civil Aviation Flight University of China, Guanghan Sichuan, 618300, China

As the core equipment for aerospace product compression molding, the strength, stiffness, and dynamic stability of aviation high-precision hydraulic presses’ four-column frame directly determine product molding accuracy and production safety. This paper optimizes the frame structure and conducts multi-condition finite element analysis via ANSYS. Static strength analysis identifies initial stress concentration; after improvement, the maximum stress in pre-tightening and working states decreases by 41.87% and 66.20% respectively. Modal analysis shows uniform deformation of the first ten modes and confirms columns as the weak link, whose inner slope is optimized for optimal load-bearing. Under 5mm eccentric loads, the maximum stress does not exceed the material yield limit, and deformation is ≤1.06mm. The improved structure effectively solves stress concentration, enhances eccentric load resistance and dynamic stability, providing a structural guarantee for reliable operation.

Keywords: Aviation high-precision hydraulic press; Frame structure; Finite element analysis; Static strength; Modal analysis; Eccentric load condition; Structural optimization
Grants and funding:

Thanks for the supports from the project "Standards for Emerging Engineering Majors and Construction of Characteristic Teaching Experiment Platforms" [Civil Aviation Education Talent Programs in China, NO. MHJY2025036], the open project "Research on the Color Recognition and Appearance Defect Detection System for Solar Cells" [Key Laboratory of Solar Energy Technology Integration and Application Promotion in Sichuan Provincial Universities, Grant No. TYNSYS-2018-Y-06], the project "Research on SLAM for Intelligent Civil Aviation Transportation Robots Based on Stereo Vision" [Civil Aviation Flight University of China, Grant No. 25CAFUC04024], and the project "Design of a Single-Star Simulation System for Calibration of Aviation Attitude Determination Star Sensors" [Chengdu Aeronautic Industry and Cultural Development Research Center, Grant No. CAIACDRCXM2024-04]

Received: March 9, 2026; Revised: July 14, 2026; Accepted: September 14, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Dong L, Fu Y, Pang J, Nie R, Hua Z. Design and Analysis of High-Precision Hydraulic Press Frame for Aviation Based on Finite Element Method. Manufacturing Technology. 2026;26(4):396-407. doi: 10.21062/mft.2026.041.
Download citation

References

  1. KARMIRIS-OBRATAŃSKI, P., PAPAZOGLOU, E.L., LESZCZYŃSKA-MADEJ, B., ZAGÓRSKI, K., MARKOPOULOS, A.P. (2021). A Comprehensive Study on Processing Ti-6Al-4V ELI with High Power EDM. Materials, Vol. 14, No. 2, pp. 303. https://doi.org/10.3390/ma14020303 Go to original source...
  2. YANG, S., WANG, P., WANG, X. (2024). Comparative analysis between theoretical calculation and practical deformation of heavy forging hydraulic press (in Chinese). China Metalforming Equipment & Manufacturing Technology, Vol. 59, No. 2, pp. 18-25. https://doi.org/10.16316/j.issn.1672-0121.2024.02.003 Go to original source...
  3. OTHMAN, S.M., SUNAR, N., ISMAIL, A.H., AYOB, M.N., AZMI, M.M., HASHIM, M.S.M. (2021). Position tracking performance with fine-tune Ziegler-Nichols PID controller for electro-hydraulic actuator in aerospace vehicle model. Journal of Physics: Conference Series, Vol. 2107, No. 1, pp. 012064. DOI 10.1088/1742-6596/2107/1/012064 Go to original source...
  4. LIN, F., YAO, W., QIN, G.H., YE, H.C., TAO, J. (2021). Coupling effect of initial residual stress and initial geometric error on machining deformations of aeronautical monolithic components and its control. Acta Armamentarii, Vol. 42, No. 12, pp. 2731-2742. DOI: 10.3969/j.issn.1000-1093.2021.12.021 Go to original source...
  5. LIM, E., HWANG, S.J. (2016). Modeling of the strut-and-Modeling of the strut-and-tie parameters of deep beams for shear strength prediction. Engineering Structures, Vol. 108, pp. 104-112. https://doi.org/10.1016/j.engstruct.2015.11.024 Go to original source...
  6. ĒAKIROĞLU, R. (2022). Analysis of EDM machining parameters for keyway on Ti-6Al-4V alloy and modelling by artificial neural network and regression analysis methods. Sādhanā, Vol. 47, No. 3, pp. 150.https://doi.org/10.1007/s12046-022-01926-y Go to original source...
  7. LIU, Y.Y., XI, J.L., BAI, H.F., WANG, Z.N., SUN, L.L. (2021). A general robot inverse kinematics solution method based on improved PSO algorithm. IEEE Access, Vol. 9, pp. 32341-32350.DOI: 10.1109/ACCESS.2021.3059714 Go to original source...
  8. WOLFGARTEN, M., RUDOLPH, F., HIRT, G. (2020). Analysis of process forces and geometrical correlations for open-die forging with superimposed manipulator displacements. Journal of Materials Processing Technology, Vol. 276, pp. 116408. https://doi.org/10.1016/j.jmatprotec.2019.116408 Go to original source...
  9. WANG, Y.F., WANG, C., XU, Y.T., SUN, R., XIAO, K., WANG, K.L. (2024). A digital twin task scheduling method for intelligent manufacturing unit operations under edge-cloud collaboration (in Chinese). Journal of Mechanical Engineering, Vol. 60, No. 6, pp. 137-152. DOI: 10.3901/JME.2024.06.137 Go to original source...
  10. ZHOU, Y.X., CHEN, Y., DENG, F., HU, X.H. (2024). Research on deformation control technology of large integral wall panel machining. Tool Engineering, Vol. 58, No. 3, pp. 102-106. DOI: 10.3969/j.issn.1000-7008.2024.03.017 Go to original source...
  11. AVERSA, R., PETRESCU, R.V., AKASH, B., BUCINELL, R., CHEN, G., LI, S., PETRESCU, F.I. (2017). Kinematics and Forces to a New Model Forging Manipulator. American Journal of Applied Sciences, Vol. 14, No. 1, pp. 60-80. DOI: 10.3844/ajassp.2017.60.80 Go to original source...
  12. LIN, F., YAO, W., QIN, G.H., YE, H.C., TAO, J. (2021). Coupling effect of initial residual stress and initial geometric error on machining deformations of aeronautical monolithic components and its control. Acta Armamentarii, Vol. 42, No. 12, pp. 2731-2742. DOI: 10.3969/j.issn.1000-1093.2021.12.021 Go to original source...
  13. KE, S.T., DU, L.Y., GE, Y.J., TAMURA Y. (2018). Multi-dimensional wind vibration coefficients under suction for ultra-large cooling towers considering ventilation rates of louvers. Structural engineering and mechanics: An international journal, Vol. 66, No. 2, pp. 273-283. https://doi.org/10.12989/sem.2018.66.2.273 Go to original source...
  14. WANG, G., HUANG, P. (2022). Innovative Design of a Hydraulic Press Mobile Station Based on TRIZ Theory. Engineering Proceedings, Vol. 24, No. 1, pp. 10. https://doi.org/10.3390/IECMA2022-12889 Go to original source...
  15. AWAIS, M., SORVARI, J., TANNINEN, P., LEPPÄNEN, T. (2022). Finte element analysis of the press forming process. International Journal of Mechanical Sciences, Vol. 131-132, pp. 767-775. https://doi.org/10.1016/j.ijmecsci.2017.07.053 Go to original source...
  16. ZEMANOVA, J., CABRNOCH, B., KRAL, M. (2026). Thermoplastic resin flow behaviour in foam core sandwich composites for aerospace applications during vacuum infusion process. Manufacturing Technology, Vol. 26, No. 2, pp. 249-256. https://doi.org/10.21062/mft.2026.018 Go to original source...
  17. BREZNICKĮ, A., MIKU©, P., TIMĮROVĮ, „., KOHUTIAR, M., KRBA«A, M. (2024). Possibilities of analyzing sources of impurities in hydraulic oil. Manufacturing Technology, Vol. 24, No. 5, pp. 721-730. https://doi.org/10.21062/mft.2024.081 Go to original source...
  18. XU, W., ZHAO, X., SHI, H., HUANG, L. (2025). Study on trapped oil and cavitation of jet fuel gear pump. Manufacturing Technology, Vol. 25, No. 1, pp. 131-142. https://doi.org/10.21062/mft.2025.005 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.