Manufacturing Technology 2026, 26(4):446-452 | DOI: 10.21062/mft.2026.042

The Effect of Accelerated Weathering on the Properties of Coatings on an Aluminum Substrate

Katarína Moricová ORCID...1, Jana ©ulcová ORCID...1, Iveta Papučová ORCID...1, Róbert Janík ORCID...1, Aleksandra Ewa Nowicka ORCID...2
1 Faculty of Industrial Technologies, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovak Republic
2 FunGlass – Centre for Functional and Surface Functionalized Glass, Alexander Dubcek University of Trenčín, ©tudentská 2, 911 50, Trenčín, Slovak Republic

Oxide coatings ZnO and TiO2 are characterized by good chemical stability, non-toxicity, photocatalytic activity, and the potential to improve the corrosion resistance of underlying materials. The aim of this study is to prepare and evaluate these environmentally friendly coatings applied to an aluminium sub-strate, which is one of the most widely used technical metals. X-ray fluorescence spectrometry employed was used to determine the chemical composition. Surface properties were investigated by measuring the contact angle on samples before exposure to UV radiation and condensation, and after 98 and 196 hours of exposure in a UV chamber. The structure of the prepared samples was analysed using atomic force microscopy (AFM). Based on the obtained results, it can be concluded that plasma treatment of the alu-minium substrates increases the surface free energy (SFE). However, after exposure to controlled UV radiation and condensation (196 hours), the hydrophilicity of the surface increases to approximately the same value for all prepared samples. Samples coated with ZnO were found to be less stable under the given conditions compared to TiO₂-coated samples and exhibited higher surface roughness.

Keywords: Contact angle, UV radiation, Aluminium substrate, Oxide coatings, Atomic force microscopy
Grants and funding:

This work was supported by the Slovak Republic Grant Agency under the KEGA project 009TnUAD-4/2026

Received: June 23, 2026; Revised: June 23, 2026; Accepted: October 25, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Moricová K, ©ulcová J, Papučová I, Janík R, Nowicka AE. The Effect of Accelerated Weathering on the Properties of Coatings on an Aluminum Substrate. Manufacturing Technology. 2026;26(4):446-452. doi: 10.21062/mft.2026.042.
Download citation

References

  1. CALLISTER, W. D., RETHWISCH, D. G. (2014). Materials Science and Engineering: An Introduction. 9th ed. Hoboken: Wiley, ISBN 978-1-118-32457-8.
  2. POLMEAR, I. J. (2005). Light Alloys: From Traditional Alloys to Nanocrystals, 4th ed. Oxford: Butterworth-Heinemann, ISBN 978-0-7506-6371-7. Go to original source...
  3. ZUPANIČ, F. et al. (2021). Structure and Properties of Aluminium Alloys, Basel: MDPI, ISBN 978-3-0365-1008-8.
  4. VARGEL, C. (2020). Corrosion of Aluminium. 2nd ed. Oxford: Elsevier, ISBN 978-0-08-099925-8. Go to original source...
  5. MIKU©, P., BREZNICKÁ, A., KOHUTIAR, M., et al. (2025), Experimental investigation of the effect of fuel on engine oil life. In: Manufacturing Technology, Vol. 25, No. 5, pp. 655-661, DOI: 10.21062/mft.2025.068. Go to original source...
  6. ĆURKOVIĆ, L., ĆURKOVIĆ, H., SPILLER, S., RENJO, M., ©EGOTA, S. (2013). Enhancement of corrosion protection of AISI 304 stainless steel by nanostructured sol-gel TiO2 films. In: Corrosion Science, Vol. 77, pp. 176-184, DOI:10.1016/j.corsci.2013.07.045 Go to original source...
  7. KUZNETSOV, Y. I., REDKINA, G. V. (2022). Thin Protective Coatings on Metals Formed by Organic Corrosion Inhibitors in Neutral Media. In: Coatings, Vol. 12, No. 2, DOI: 10.3390/coatings12020149. Go to original source...
  8. AWANG, M., KHALILI, A. A., PEDAPATI, S. R. (2020). A Review: Thin Protective Coating for Wear Protection in High-Temperature Application. In: Metals, Vol. 10, No. 42, DOI: 10.3390/met10010042. Go to original source...
  9. ©ULCOVÁ, J., PAPUČOVÁ, I., et al. (2024). The Effect of TiO2 Layers on the Surface Properties of Materials. In: Manufacturing Technology, Vol. 24, No. 2, pp. 272-278, DOI: 10.21062/mft.2024.022. Go to original source...
  10. METROKE, T.L., PARHHILL, R.L., KNOBBE, E.T. (2011). Passivation of metal alloys using sol-gel-derived materials-review. In: Progress in Organic Coating, Vol. 41, pp. 233-238, DOI:10.1016/S0300-9440(01)00134-5 Go to original source...
  11. HAMID, M.A., RAHMAN, I. A. (2003). Preparation of titanium dioxide (TiO2) thin films by sol gel dip coating method. In: Malaysian Journal of Chemistry, Vol. 5, pp. 86-91.
  12. CUAO MOREU, C. A. et al. (2026). Plasma-Driven Surface Functionalization: Enhancing the Corrosion Resistance of Aluminium via Atmospheric-Pressure Treatment. In: Materials, Vol. 19, No. 973, DOI: 10.3390/ma19050973 Go to original source...
  13. JANÍK, R., LABAJ, I., SKALKOVÁ, P., ĎURI©OVÁ, S., MORICOVÁ, K., (2024). Effects of Filler Modification on the Properties of Elastomeric Composites, In: Manufacturing Technology, Vol. 24, No. 3, pp. 365-377, DOI:10.21062/mft.2024.056. Go to original source...
  14. BAKO©OVÁ, D., BAKO©OVÁ, A. (2021). Analysis of Homogeneity and Young's Moduli of Rubber Compounds by Atomic Force Microscopy. In: Manufacturing Technology, Vol. 21, No. 6, pp. 749-756, DOI: 10.21062/mft.2021.099. Go to original source...
  15. TSAI, D. C. et al (2023). Influence of Plasma Treatment on Surface Characteristics of Aluminum Alloy Sheets and Bonding Performance of Composites. In: Materials, Vol.16, 3317. DOI: 10.3390/ma16093317. Go to original source...
  16. BINDER, W. H., SPERLING, E. (2021). Recent Developments in Surface Morphology Characterization of Functional Materials. In: Surface and Interface Analysis, Vol. 53, pp. 305-324. DOI: 10.1002/sia.6931. Go to original source...
  17. LI, C., WANG, Z., YANG, J. (2024). Surface Morphology Evolution in Plasma Treated Metals. In: Journal of Materials Science and Technology, Vol. 105, pp. 152-162. DOI: 10.1016/j.jmst.2023.10.016. Go to original source...
  18. LEACH, R. (2013). Characterisation of Areal Surface Texture. Berlin: Springer, ISBN 978-3-642-36458-7. Go to original source...
  19. ECKSCHLAGER, K., HORSÁK, I., KODEJ©, Z. (1980). Vyhodnocování analytických výsledků a metod. 1. vyd. Praha: SNTL, s.51.
  20. MUÑOZ, J., RINCÓN, R., CALZADA, M.D. (2019). Spatial Distribution of Wettability in Aluminum Surfaces Treated with an Atmospheric-Pressure Remote-Plasma. In: Metals, Vol. 9, pp. 937. DOI: 10.3390/met9090937. Go to original source...
  21. MA, C., NIKIFOROV, A.; HEGEMANN, D., DE GEYTER, N., MORENT, R., OSTRIKOV, K. (2022). Plasma-controlled surface wettability: recent advances and future applications. In: International Materials Reviews, Vol. 68, No. 7, pp. 1-38. DOI:10.1080/09506608.2022.2047420. Go to original source...
  22. CHEN, X.; SELLONI, A. (2014). Titanium Dioxide (TiO2) Nanomaterials. In: Chemical Reviews. Vol. 114, No. 19. Go to original source...
  23. XIAODONG, W, GUANGMING, W., et al. (2013). Optical Constants of Crystallized TiO2 Coatings Prepared by Sol-Gel Process. In. Materials. Vol. 6, pp. 2819-2830, DOI:10.3390/ma6072819. Go to original source...
  24. JITAO, Z., WILLIAMS, G., THANAPHUN, J., et al. (2024). Wettability and Bactericidal Properties of Bioinspired ZnO Nanopillar Surfaces. In: Langmuir. Vol. 40, No. 14, pp. 7353-7363, DOI: 10.1021/acs.langmuir.3c03537. Go to original source...
  25. BINGYAO, D., XIONG, Y., QUFU, W., WEIDONG, G., (2007) AFM characterization of nonwoven material functionalized by ZnO sputter coating. In: Materials Characterization. Vol. 58, pp. 854-858. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.