Manufacturing Technology 2026, 26(4):424-432 | DOI: 10.21062/mft.2026.044
Experimental Evaluation of the Influence of Different Types of Lubricants on the Tribological Resistance of Quenched and Tempered 42CrMo4 Steel
- 1 Armed Forces Academy of General Milan Rastislav ©tefánik, Demänová 393, 031 01 Liptovský Mikulá¹, Slovakia
- 2 Faculty of Special Technology, Alexander Dubcek University of Trenèín, Ku Kyselke 469, 911 06 Trenèín, Slovakia
This study investigates the influence of selected commercially available lubricants on the tribological behaviour of quenched and tempered 42CrMo4 steel intended for highly loaded mechanical and firearm components. Ten oils available on the domestic market were selected according to their ability to reduce friction, protect metallic surfaces and avoid silicone or PTFE-based additives. Reciprocating Ball-on-flat tests were performed using a Bruker UMT TriboLab with a G40 steel ball under a normal load of 50 N, a stroke length of 10 mm, a sliding speed of 0.3 m/min and a test duration of 20 min. The worn surfaces were evaluated using a LEXT OLS5100 3D laser confocal microscope. The dry reference sample reached the highest coefficient of friction, μ = 0.548, and the highest wear volume, 0.11127 mm³. In contrast, all lubricated samples showed substantially lower friction values, μ = 0.102–0.131, and wear volumes of 0.00264–0.00491 mm³. The best performance was achieved by BRUNOX® LUB&COR®, which provided the lowest friction coefficient and wear volume. Morphological analysis revealed severe adhesive and abrasive wear under dry conditions, whereas lubricated surfaces exhibited reduced damage and protective tribo-oxidative layers. The results confirm that lubricant viscosity, film stability and surface interactions significantly affect friction and wear of 42CrMo4 steel.
Keywords: Steel, Coefficient of friction, Wear, Lubrication
Grants and funding:
This work was supported by the Ministry of Education, Research, Development, and Youth of the Slovak Republic under contract no. VEGA 1/0260/26, “Experimental research on the optimization of Q&P heat treatment parameters to increase the tribological resistance of advanced high-strength AHSS steels with medium Mn content“
Received: July 11, 2026; Revised: July 11, 2026; Accepted: October 26, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026 Show citation
| ACS | AIP | APA | ASA | Harvard | Chicago | Chicago Notes | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- DOBROCKÝ, D., JOSKA, Z., PROCHÁZKA, J., SVOBODA, E., DOSTÁL, P. (2021). Evaluation of Structural and Mechanical Properties of the Nitrided Layer on Steel for Weapons. In: Manufacturing Technology, Vol. 21, No. 2, pp. 183-191. DOI: 10.21062/mft.2021.031.
Go to original source... - KRBA«A, M., MAJERÍK, J., BARÉNYI, I., MIKU©OVÁ, I., KUSMIÈ, D. (2019). Mechanical and Tribological Features of the 90MnCrV8 Steel after Plasma Nitriding. In: Manufacturing Technology, Vol. 19, No. 2, pp. 238-242.
Go to original source... - JA©©O, M., PASTIRÈÁK, R., FABIAN, P., BRONÈEK, J. (2026). Applications of the Boriding Process in the Defence Industry. In: Manufacturing Technology, Vol. 26, No. 3. DOI: 10.21062/mft.2026.030.
Go to original source... - DOAN, T. V., KUSMIÈ, D., POSPÍCHAL, M., TRAN, Q. D., NGUYEN, V. T. (2017). Friction and Wear Behaviour of 42CrMo4 Steel Treated by Tenifer, Hard Chrome and Plasma Nitriding Technologies. In: Manufacturing Technology, Vol. 17, No. 2, pp. 14-15.
Go to original source... - AUTAY, R., KCHAOU, M., DAMMAK, F. (2015). Experimental Investigation of the Tribological Behaviour of Carbon and Low-Alloy Steels Sliding against HSS. In: Mechanics & Industry, Vol. 16, Art. No. 109. DOI: 10.1051/meca/2014076.
Go to original source... - SOFRONOV, Y., DOCHEV, B., MISHEV, V., NIKOLOV, A., PETROV, K., DIMITROVA, R., YORDANOV, M., ANGELOV, M., TODOROV, G., MARCHEV, K. (2026). Investigation of the Mechanical Properties and Friction Coefficient of Cr/CrTiAl and Cr/(CrTiAl)N/CrTiAl PVD Coatings Deposited on 42CrMo4 QT Steel. In: Metals, Vol. 16, Art. No. 231. DOI: 10.3390/met16020231.
Go to original source... - GALDA, L., DZIERWA, A., PAWLUS, P., REIZER, R. (2011). Improvement of Tribological Properties of Co-Acting Elements by Oil Pockets Creation on Sliding Surfaces. In: Meccanica, Vol. 46, pp. 523-534. DOI: 10.1007/s11012-010-9300-5.
Go to original source... - ¦WIRAD, S., PAWLUS, P. (2020). The Effect of Ball Burnishing on Tribological Performance of 42CrMo4 Steel under Dry Sliding Conditions. In: Materials, Vol. 13, Art. No. 2127. DOI: 10.3390/ma13092127.
Go to original source... - PANFIL-PRYKA, D., KULKA, M., KOTKOWIAK, M., MICHALSKI, J., GROCHALSKI, K. (2025). Tribological Behavior of Gas-Nitrided 42CrMo4 Steel at Elevated Temperatures. In: Coatings, Vol. 15, Art. No. 18. DOI: 10.3390/coatings15010018.
Go to original source... - SKULIÆ, A., MILOJEVIÆ, S., MARIÆ, D., IVANOVIÆ, L., KRSTIÆ, B., RADOJKOVIÆ, M., STOJANOVIÆ, B. (2022). The Impact of Lubricant Viscosity and Materials on Power Losses and Efficiency of Worm Gearbox. In: Tehnièki vjesnik, Vol. 29, No. 6, pp. 1853-1860. DOI: 10.17559/TV-20220207092015.
Go to original source... - KUSMIC, D., DOAN, T. V., PILCH, O., KRBA«A, M. (2016). Corrosion Resistance and Tribological Properties of Plasma Nitrided and Tenifered 42CrMo4 Steel. In: Proceedings of the 25th Anniversary International Conference on Metallurgy and Materials, Brno, Czech Republic, pp. 25-27.
Go to original source... - PAWLUS, P., DZIERWA, A. (2018). Wear Analysis of Discs and Balls on a Micro-Scale. In: Tehnièki vjesnik, Vol. 25, Suppl. 2, pp. 299-305. DOI: 10.17559/TV-20160530222544.
Go to original source... - WU, F., JIANG, Z., LIU, Z., SUN, Y., LI, X. (2023). Analysis of Influencing Factors on the Tribological Behavior of 42CrMo4/17NiCrMo6-4 under Grease Lubrication. In: Materials, Vol. 16, Art. No. 6699.
Go to original source... - DAVIM, J. P. (2007). Wear: Materials, Mechanisms and Practice. John Wiley & Sons, Chichester. ISBN 978-0-470-01628-2.
- KOHUTIAR, M., KRBATA, M., ESCHEROVA, J., ECKERT, M., MIKUS, P., JUS, M., POLÁ©EK, M., JANÍK, R., DUBEC, A. (2024). The Influence of the Geometry of Movement during the Friction Process on the Change in the Tribological Properties of 30CrNiMo8 Steel in Contact with a G40 Steel Ball. In: Materials, Vol. 17, Art. No. 127. DOI: 10.3390/ma17010127.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.



ORCID...