Manufacturing Technology 2026, 26(4):461-472 | DOI: 10.21062/mft.2026.045
Evaluation of Formability of Laser Tailor Welded Blanks
- Institute of technologies and materials, Faculty of Mechanical Engineering, STU Bratislava, Nám. Slobody 17, 812 31 Bratislava. Slovakia
The car body construction is made from workpieces on which specific demands are put. The high stiffness and strength, low weight, programmable deformability is achieved by using of tailored welded blanks (TWBs). The weld joint is most commonly realized by a laser weld with a narrow heat affected zone (HAZ). The formability of TWB is affected by the weld, stress-strain characteristics of materials and process conditions. For the analysis of TWBs, materials with the same thickness, but different orientation of the texture of the individual parts with respect to the position of the weld, were used. The effect of surface anisotropy of individual materials on formability was studied in terms of the origin and direction of crack propagation during deep drawing or tension test. The sensitivity of individual materials to the presence of a weld, the formation of a crack and the course of changes in microhardness in the weld and HAZ was evaluated. The obtained results are important in the design of TWB from the point of view of the presence of a weld and the orientation of the texture of individual parts of the TWB in relation to local limit strains and the risk of cracks formation.
Keywords: Deep drawing, Tailor welded blank, Weld, Crack, Anisotropy
Grants and funding:
This work was supported by the University Science Park STU Bratislava ITMS code 26240220084. We would like to thank the Slovak grant agency VEGA for the financial support of the project VEGA 1/0302/23
Received: June 18, 2026; Revised: October 28, 2026; Accepted: November 5, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026 Show citation
References
- EVIN, E., TOMÁŠ, M. (2012). Comparison of deformation properties of steel sheets for car body parts. In: Procedia Engineering, Vol. 48, pp.115-122.
Go to original source... - EVIN, E. (2013). Design of dual phase high strength steels sheet for auto body. In: 22nd International Conference on Metallurgy and Materials - METAL 2013. Ostrava: Tanger.
- HRIVŇÁK, A., EVIN, E. (2004). Formability of Steel Sheets, 1st ed.; Alfa: Košice, Slovakia.
- www.arcelormittal.com
- MEŠKO, J., ZRAK, A., MULCZYK, K., TOFIL, S. (2014). Microstructure Analysis of Welded Joints after Laser Welding. In: Manufacturing Technology, Vol. 14, No. 3, pp. 355-359.
Go to original source... - EVIN, E., TOMÁŠ, T. (2017). The Influence of Laser Welding on the Mechanical Properties of Dual Phase and Trip Steels, In: Metals, Vol. 7, p. 239.
Go to original source... - MERKLEIN, M., JOHANNES, M., LECHNER, M., KUPPERT, A. (2014). A review on tailored blanks - Production, applications and evaluation. In: J. Mater. Process. Technol., Vol. 214, pp. 151-164.
Go to original source... - PODANY, P., REARDON, C., KOUKOLIKOVA, M., PROCHAZKA, R., FRANC, A. (2018). Microstructure, Mechanical Properties and Welding of Low Carbon, Medium Manganese TWIP/TRIP Steel. In: Metals, Vol. 8, p. 263
Go to original source... - XIE, J., MA, Y., OU, M., XING, W., ZHANG, L., LIU, K. (2018). Evaluating the Microstructures and Mechanical Properties of Dissimilar Metal Joints Between a New Cast Superalloy K4750 and Hastelloy X Alloy by Using Different Filler Materials. In: Materials, Vol. 11, p. 2065.
Go to original source... - VILLALOBOS, J.C., DEL-POZO, A., CAMPILLO, B., MAYEN, J., SERNA, S. (2018). Microalloyed Steels through History until 2018: Review of Chemical Composition, Processing and Hydrogen Service. Metals, Vol. 8, p. 351.
Go to original source... - KOREČEK, D., SOLFONK, P., SOBOTKA, J. (2023). Utilization of Metal Forming Process Mathematical Modelling to Predict the Spring-back of the Dual-phase Steel Stamping. In: Manufacturing Technology, Vol. 23, No. 6, pp. 827-836.
Go to original source... - GAUTAM, V., KUMAR, A. (2019). Experimental and Numerical Studies on Formability of Tailor Welded Blanks of High Strength Steel. In: Procedia Manuf., Vol. 29, pp. 472-480.
Go to original source... - MUJICA, L., WEBER, S., PINTO, H., THOMY, C., VOLLERTSEN, F. (2010). Microstructure and mechanical properties of laser-welded joints of TWIP and TRIP steels. In: Mater. Sci. Eng. A, Vol. 527, pp. 2071-2078.
Go to original source... - ZDRAVECKÁ, E., SLOTA, J. (2019). Mechanical and Microstructural Investigations of the Laser Welding of Different Zinc-Coated Steels. Metals, Vol. 9, p. 91.
Go to original source... - DOU, S., WANG, X., XIA, J., WILSON, L. (2020). Analysis of Sheet Metal Forming (Warm Stamping Process): A Study of the Variable Friction Coefficient on 6111 Aluminum Alloy. In: Metals, Vol.10, 1189.
Go to original source... - PANDA, S.K., RAVI KUMAR, D. (2010). Experimental and numerical studies on the forming behavior of tailor welded steel sheets in biaxial stretch forming. In: Mater. Des., Vol. 31, pp. 1365-1383.
Go to original source... - ČADA, R. (2001). Formability of steel sheets. 346 s. REPRONIS, Ostrava. ISBN 80-86122-77-8
- SOBOTKA, J., BRADÁČ, J. (2019). Measurement of the Anisotropy Coefficient Development in Dependence on Deformation. In: Manufacturing Technology, Vol. 19, No. 4, pp. 692-699.
Go to original source... - ŘIHÁČEK, J., PODANÝ, K., FALTÝNEK, F. (2019). Prediction of the Stamped Part Thinning Depending on Its Geometry and Blank Material. In: Manufacturing Technology, Vol. 19, No. 2, pp. 314-320.
Go to original source... - SAFDARIAN, K. R., MOSLEMI N. H., TORKAMANY, M.J., LIAGHAT, G. (2013). Experimental and theoretical investigation of thickness ratio effect on the formability of tailor welded blank. In: Opt. Laser. Technol., Vol. 51, pp. 24-31.
Go to original source... - PANDRE, S., KOTKUNDE, N., TAKALKAR, P., MORCHHALE, A., SUJITH R., SINGH K.S. (2019). Flow stress behavior, constitutive modeling, and microstructural characteristics of DP 590 steel at elevated temperatures. In: J. Mater Eng Perform., Vol. 28, pp. 7565-7581.
Go to original source... - CHOI, S. H., KIM, E. Y., WOO, W., HAN, S. H., KWAK, J. H. (2013). The efect of crystallographic orientation on the micromechanical deformation and failure behaviors of DP980 steel during uniaxial tension. In: Int J Plast, Vol. 45, pp. 85-102.
Go to original source... - SCHREK, A., ŠVEC, P., BRUSILOVÁ, A. (2014). Formability of Tailor-Welded Blanks From Dual-Phase and Bake-Hardened Steels with a Planar Anisotropy Influence. In: Strength of Materials, Vol. 49, pp. 550-554.
Go to original source... - SONG, Y., HUA, L. (2014). Influences of thickness ratio of base sheets on formability of Tailor Welded Blanks. In: Procedia Eng., Vol. 81, pp. 730-735.
Go to original source... - PANDRE, S., TAKALKAR, P., MORCHHALE, A., KOTKUNDE, N., SINGH, K. S. (2020). Prediction capability of anisotropic yielding behaviour for DP590 steel at elevated temperatures. In: Adv Mater Process Technol, Vol. 6, No. 2, pp. 396-404.
Go to original source... - KOREČEK, D., SOLFRONK, P., SOBOTKA, J. (2022). Analysis of the Dual-phase Steel DP500 Stress-strain Characteristics During the Plane Shear Test. In: Manufacturing Technology, Vol. 22, pp. 34-38.
Go to original source... - ŠVEC, P., CSICSÓ, T., SCHREK, A., BRUSILOVÁ, A. (2016). Zváranie tenkých plechov z ocelí HCT980X a HX220BD pevnolátkovým vláknovým laserom. In Zváranie 2016 [elektronický zdroj] : 44. medzinárodná konferencia, Tatranská Lomnica, 9.-11. november 2016. Zborník. 1. vyd. Bratislava : Slovenská zváračská spoločnosť, pp. 166-174. ISBN 978-80-89296-19-4.
- CSICSÓ, T., ŠVEC, P., SCHREK, A., GÁBRIŠOVÁ, Z. (2016). Štruktúra laserových zvarových spojov z ocelí HCT 600X, HCT980X a HX220BD. In Zváranie 2016 [elektronický zdroj] : 44. medzinárodná konferencia, Tatranská Lomnica, 9.-11. november 2016. Zborník. 1. vyd. Bratislava : Slovenská zváračská spoločnosť.
- SCHREK, A., ŠVEC, P., BRUSILOVÁ, A. (2017). Formability of Tailor-Welded Blanks From Dual-Phase and Bake-Hardened Steels with a Planar Anisotropy Influence. In Strength of Materials. Vol. 49, No. 4, pp. 550-554.
Go to original source... - ŠVEC, P., SCHREK, A., HRNČIAR, V., CSICSÓ, T. (2015). Fibre laser welding of dual phase steels. In Acta Metallurgica Slovaca. Vol. 21, N o. 4, pp. 311-320. ISSN 1335-1532.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.



ORCID...