Manufacturing Technology 2026, 26(4):487-496 | DOI: 10.21062/mft.2026.046

Effect of Liquid Nitrogen Cooling on Machinability and Tool Wear Mechanisms in Cutting CGI-400

Shanshan Xu ORCID...1, Xu Sun ORCID...2, Fanning Meng ORCID...1, Yingqi Shen ORCID...1, Chunjing Shi ORCID...1, Ying Yang ORCID...1
1 School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, China
2 Hangzhou Shuzhi Innovation Transportation Technology Development Co., Ltd., Hangzhou 310000, China

This study systematically investigates the performance of liquid nitrogen cooling in machining compacted graphite iron 400 (CGI-400), compared with conventional cutting fluid cooling, focusing on mechanical properties, cutting temperature, tool wear, and surface quality. Results indicate that liquid nitrogen cooling significantly reduces the cutting temperature by 22.38%, effectively suppresses flank wear and built-up edge formation, and demonstrates remarkable advantages at cutting lengths beyond 3000 m. Cryogenic embrittlement of CGI-400 under liquid nitrogen leads to an 11.32% reduction in tensile strength, while the temperature-dependent thermal conductivity influences heat management in the cutting zone. EDS analysis reveals less material adhesion and improved coating integrity under liquid nitrogen cooling, contributing to prolonged tool life and enhanced surface finish. This research provides theoretical and practical insights into the cryogenic machining of CGI-400.

Keywords: Liquid nitrogen cooling, CGI-400, Tool wear, Cutting temperature, Surface roughness
Grants and funding:

This research was funded by Zhejiang Provincial Natural Science Foundation of China under Grant (LQN25E050017), the Fundamental Research Funds for the Provincial Universities of Zhejiang (GK259909299001-035), the Young Scientists Fund of the National Natural Science Foundation of China (52305530, 12202128), and the Ninth China Association for Science and Technology Youth Talent Lift Project Support Plan (YESS20230359)

Received: June 2, 2026; Revised: October 26, 2026; Accepted: November 6, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Xu S, Sun X, Meng F, Shen Y, Shi C, Yang Y. Effect of Liquid Nitrogen Cooling on Machinability and Tool Wear Mechanisms in Cutting CGI-400. Manufacturing Technology. 2026;26(4):487-496. doi: 10.21062/mft.2026.046.
Download citation

References

  1. ZHENG L. J., LAI Z. W., SUN Y., et al. The machining of compacted graphite irons - State of the art and future perspective[J]. Machining Science and Technology, 2025, 29(1): 118-157. Go to original source...
  2. TAN J., WANG J. P., HAO X. Q., et al. Research on coated wiper insert for milling of compacted graphite iron[J]. The International Journal of Advanced Manufacturing Technology, 2024, 132(3-4): 1237-1249. Go to original source...
  3. JAN B.. Measurement of heat transfer in a sand mould foundry - optimisation of cooling time for cast iron and ductile cast iron mass castings[J]. Manufacturing Technology, 2025, 25(2): 161-169. Go to original source...
  4. WOLLMANN D., DE MIRANDA M. A., PINTAUDE G., et al. Abrasive wear resistance of high-strength compacted graphite iron under microabrasion conditions[J]. Lubricants, 2022, 10(11): 308. Go to original source...
  5. GRZESIK W., RECH J., ¯AK K., et al. Machining performance of pearlitic-ferritic nodular cast iron with coated carbide and silicon nitride ceramic tools[J]. International Journal of Machine Tools and Manufacture, 2009, 49(2): 125-133. Go to original source...
  6. MALAKIZADI A., SADIK I., NYBORG L. Wear mechanism of CBN inserts during machining of bimetal aluminum-grey cast iron engine block[J]. Procedia CIRP, 2013, 8: 188-193. Go to original source...
  7. TOOPTONG S., PARK K. H., KWON P. A comparative investigation on flank wear when turning three cast irons[J]. Tribology International, 2018, 120: 127-139. Go to original source...
  8. ABELE E., SAHM A., SCHULZ H. Wear mechanism when machining compacted graphite iron[J]. CIRP Annals-Manufacturing Technology, 2002, 51(1): 53-56. Go to original source...
  9. LINDVALL R., DIAZ K. M., PENG R. L., et al. Wear mechanisms in Ti(C,N)-Al2O3 coated carbide during sustainable machining CGI[J]. International Journal of Refractory Metals and Hard Materials, 2024, 119: 106550. Go to original source...
  10. MOHAMMED W. M., NG E., ELBESTAWI M. A. Modeling the effect of the microstructure of compacted graphite iron on chip formation[J]. International Journal of Machine Tools and Manufacture, 2011, 51(10-11): 753-765. Go to original source...
  11. ONDREJ B., JAN O., PETR J., et al. Microtexturing for enhanced machining: evaluating tool performance in laser-processed cutting inserts[J]. Manufacturing Technology, 2024, 24(2):173-182. Go to original source...
  12. QIU Y., PANG J. C., LI S. X., et al. Influence of thermal exposure on microstructure evolution and tensile fracture behaviors of compacted graphite iron[J]. Materials Science and Engineering: A, 2016, 664: 75-85. Go to original source...
  13. AKINRIBIDE O. J., OGUNDARE O. D., OLUWAFEMI O. M., et al. A review on heat treatment of cast iron: phase evolution and mechanical characterization[J]. Materials, 2022, 15(20): 7109. Go to original source...
  14. SUHAIMI M. A., PARK K. H., YANG G. D., et al. Effect of cryogenic high-speed milling of compacted graphite iron using indirect spray system[J]. International Journal of Advanced Manufacturing Technology, 2018, 99: 2149-2157. Go to original source...
  15. NGUYEN D., TOOPTONG S., PARK K. H., et al. Formation mechanism of alumina layer in protecting cubic boron nitride inserts in turning cast irons[J]. International Journal of Machine Tools and Manufacture, 2020, 153: 103539. Go to original source...
  16. RAO S. V., RAMANA M. V., KUMAR A. C. S. An experimental investigation on Compact Graphite Iron wear behavior at 32℃ and 200℃[J]. Materials Today: Proceedings, 2019, 19: 778-780. Go to original source...
  17. ARAMCHAROEN A., CHUAN S. K. An experimental investigation on cryogenic milling of Inconel 718 and its sustainability assessment[J]. Procedia CIRP, 2014, 14: 529-534. Go to original source...
  18. WANG C. Y., LIN H. S., WANG X., et al. Effect of different oil-on-water cooling conditions on tool wear in turning of compacted graphite cast iron[J]. Journal of Cleaner Production, 2017, 148: 477-489. Go to original source...
  19. SUHAIMI M. A., PARK K. H., YANG G. D., et al. Effect of cryogenic high-speed milling of compacted graphite iron using indirect spray system[J]. International Journal of Advanced Manufacturing Technology, 2018, 99: 2149-2157. Go to original source...
  20. MENG F. N., ZHANG Z. Y., LI J. Q., et al. A novel approach of composite turning for compacted graphite iron using minimum quantity lubrication and liquid nitrogen jetting by a developed setup[J]. Journal of Manufacturing Processes, 2024, 117: 278-288. Go to original source...
  21. TU L. Q., CHEN J., AN Q. L., et al. Machinability improvement of compacted graphite irons in milling process with supercritical CO₂-based MQL[J]. Journal of Manufacturing Processes, 2021, 68: 154-168. Go to original source...
  22. LIN H. S., WANG C. Y., LUO J., et al. Performance of tool with hard coating when cutting compacted cast iron under different spray filed[J]. Diamond and Abrasives Engineering, 2019, 39(3): 51-57.
  23. KUZU A. T., BIJANZAD A., BAKKAL M. Experimental investigations of machinability in the turning of compacted graphite iron using minimum quantity lubrication[J]. Machining Science and Technology, 2015, 19: 559-576. Go to original source...
  24. TOOPTONG S., PARK K. H., LEE S. W., et al. A preliminary machinability study of flake and compacted graphite irons with multilayer coated and uncoated carbide inserts[J]. Procedia Manufacturing, 2016, 5: 644-657. Go to original source...
  25. NING K., WANG Q., WANG J., et al. Wear-resistant and anti-corrosion mechanism for transmission friction pairs in marine environment[J]. Friction, 2025, 13(9): 9441037. Go to original source...
  26. MENG F. N., ZHANG Z. Y., WU B., et al. Turning processes and mechanism of compacted graphite iron used for high performance engine[J]. Journal of Manufacturing Processes, 2021, 68: 951-960. Go to original source...
  27. Krzysztof K., Pavol G.. Analysis of the impact of modernization of machinery on the quality of castings using quality management tools[J]. Manufacturing Technology 2024, 24(2):207-218. Go to original source...
  28. LONG F., SONG K. X., ZHANG Z. Q., et al. Research progress on brazing copper with dissimilar materials[J]. Rare Metal Materials and Engineering, 2025, 54(3): 818-836.

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.