Manufacturing Technology 2026, 26(4):473-479 | DOI: 10.21062/mft.2026.047
Thermal Stability and Heat Treatment of Biomedical Co–28Cr–6Mo Alloy for Knee Implant Applications
- Department of Metals and Corrosion Engineering, University of Chemistry and Technology Prague. Technická 5, 166 28 Prague 6. Czech Republic
This study investigates the effect of heat treatment on cast Co–28Cr–6Mo biomedical alloy used for the production of knee implants. The alloy is widely used due to its excellent corrosion resistance, wear resistance, and mechanical properties. However, these properties can be further optimized by appropriate heat treatment. The thermal stability of the alloy was evaluated through hardness meas-urements and microstructural characterization. The highest hardness was achieved after annealing at 800 °C, which was associated with an increased fraction of the ε-phase with HCP crystal structure. In contrast, solution annealing followed by aging resulted in a microstructure dominated by the γ-phase with FCC structure and the precipitation of fine M23C6 carbides. Although both heat-treatment routes increased hardness by approximately 30 % compared to the as-cast condition, they operated through different strengthening mechanisms. The results indicate that the solution-treated and aged condition may provide a favorable combination of strength and ductility, making it a promising option for orthopedic implant applications.
Keywords: Knee implant, Microstructure, Heat treatment, Thermal stability
Grants and funding:
This research was financially supported by the Specific university research funding (A1_FCHT_2026_005) and by the project "Mechanical Engineering of Biological and Bioinspired Systems", funded as project No. CZ.02.01.01/00/22_008/0004634 by Programme Johannes Amos Commenius, call Excellent Research
Received: July 10, 2026; Revised: October 31, 2026; Accepted: November 9, 2026; Prepublished online: November 16, 2026; Published: November 17, 2026 Show citation
References
- NARUSHIMA, T.; UEDA, K.; ALFIRANO. 2015. Co-Cr Alloys as Effective Metallic Biomaterials. Advances in Metallic Biomaterials: Tissues, Materials and Biological Reactions, 157-178.
Go to original source... - DOBROVOLNA, L.; VARHANIK, M.; SEDLAK, J.; POLZER, A.; STUDENY, Z. 2021. The design of a device for testing the tribological properties of knee endoprostheses. Manufacturing Technology Journal, 21 (4), 447-455.
Go to original source... - NOVA, K.; NOVAK, P.; KNAISLOVA, A.; DVORSKY, D.; ZYKA, J. 2016. Microstructure of New Cobalt Alloy for Medical Use. Manufacturing Technology Journal, 16 (5), 1091-1095.
Go to original source... - NARUSHIMA, T.; MINETA, S.; KURIHARA, Y.; UEDA, K. 2013. Precipitates in Biomedical Co-Cr Alloys. JOM, 65 (4), 489-504.
Go to original source... - NOVA, K.; NOVAK, P.; DVORSKY, D.; ZYKA, J. 2016. Mechanical Properties of Co-Cr-Mo Alloy in Dependence in the Composition and Production. Manufacturing Technology Journal, 16 (6), 1336-1340.
Go to original source... - DA SILVA, D. J.; CONTIERI, R.; CREMASCO, A.; FLORIANO, R. 2022. The Effect of Cooling Rate on the Microstructure and Hardness of As-Cast Co-28Cr-6Mo Alloy Used as Biomedical Knee Implant. International Journal of Metalcasting, 16 (4), 2187-2198.
Go to original source... - ZHU, L.; ZHU, L.; WANG, H.; LIU, N.; LIANG, C. 2026. Simulation prediction of solidification microstructure of CoCrMo alloy investment casting under different grain refiners based on the CAFE method. International Communications in Heat and Mass Transfer, 178, 111611.
Go to original source... - ROSENTHAL, R.; CARDOSO, B. R.; BOTT, I. S.; PARANHOS, R. P. R.; CARVALHO, E. A. 2010. Phase characterization in as-cast F-75 Co-Cr-Mo-C alloy. Journal of Materials Science, 45 (15), 4021-4028.
Go to original source... - YAMANAKA, K.; MORI, M.; CHIBA, A. 2015. Assessment of precipitation behavior in dental castings of a Co-Cr-Mo alloy. Journal of the Mechanical Behavior of Biomedical Materials, 50, 268-276.
Go to original source... - ÖZTÜRK GÜLER, K.; ERTUĞRUL, O.; ÖZCAN, M. 2021. Effects of various heat treatments on microstructure and mechanical properties of investment cast Co-Cr-Mo implants. Cumhuriyet Science Journal, 42, 965-976.
- SEDLAÈEK, M.; ZUPANÈIÈ, K.; ©ETINA BATIÈ, B.; KOSEC, B.; ZORC, M.; NAGODE, A. 2023. Influence of Precipitation Hardening on the Mechanical Properties of Co-Cr-Mo and Co-Cr-W-Mo Dental Alloys. Metals, 13 (3).
Go to original source... - ROUDNICKA, M.; BIGAS, J.; MOLNAROVA, O.; PALOUSEK, D.; VOJTECH, D. 2021. Different Response of Cast and 3D-Printed Co-Cr-Mo Alloy to Heat Treatment: A Thorough Microstructure Characterization. Metals, 11 (5).
Go to original source... - MORI, M.; SATO, N.; YAMANAKA, K.; YOSHIDA, K.; KURAMOTO, K.; CHIBA, A. 2016. Development of microstructure and mechanical properties during annealing of a cold-swaged Co-Cr-Mo alloy rod. Journal of the Mechanical Behavior of Biomedical Materials, 64, 187-198.
Go to original source... - THURLOVA, H.; VOJTECH, D. 2026. Microstructure and Mechanical Properties of Biomedical Co-Cr-Mo Alloy Produced by Precision Casting and 3D Printing Technologies. Manufacturing Technology Journal, 26 (2), 233-238.
Go to original source... - VARANO, R.; BOBYN, J. D.; YUE, S. 1996. Characterization of Co-Cr-Mo Alloys Used in HIP Implant Articulating Surfaces. MRS Online Proceedings Library, 441 (1), 481-486.
Go to original source... - KAISER, R.; WILLIAMSON, K.; O'BRIEN, C.; RAMIREZ-GARCIA, S.; BROWNE, D. J. 2015. Effects of hot isostatic pressing and heat treatment on cast cobalt alloy. Materials Science and Technology, 31 (11), 1298-1304.
Go to original source... - KAISER, R.; WILLIAMSON, K.; O'BRIEN, C.; RAMIREZ-GARCIA, S.; BROWNE, D. J. 2013. The influence of cooling conditions on grain size, secondary phase precipitates and mechanical properties of biomedical alloy specimens produced by investment casting. Journal of the Mechanical Behavior of Biomedical Materials, 24, 53-63.
Go to original source... - BEDOLLA, Y.; JUÁREZ HERNANDEZ, A.; PEREZ-UNZUETA, A.; GARCIA-SANCHEZ, E.; MERCADO-SOLIS, R.; HERNANDEZ- RODRIGUEZ, M. A. L. 2009. Influence of heat treatments on mechanical properties of a biocompatility alloy ASTM F75. Revista Mexicana de Fisica, 55, 1.
- HASSANI, F. Z.; KETABCHI, M.; BRUSCHI, S.; GHIOTTI, A. 2016. Effects of carbide precipitation on the microstructural and tribological properties of Co-Cr-Mo-C medical implants after thermal treatment. Journal of Materials Science, 51 (9), 4495-4508.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.



ORCID...