Manufacturing Technology 2010, 10(1):57-64 | DOI: 10.21062/ujep/x.2010/a/1213-2489/MT/10/1/57

Non-destructive analysis of surface integrity in turning and grinding operations

Ochodek Vladislav1, Neslušan Miroslav2, Rosípal Martin2, Šípek Michal2
1 Department of Mechanical Technology, Faculty of Mechanical Engineering, VŠB-Technical University of Ostrava, 17 listopadu 15,708 33 Ostrava-Poruba, Czech Republic
2 Department of Machining and Manufacturing Engineering, Faculty of Mechanical Engineering, University of Žilina, Slovakia

This paper deals with application of Barkhausen noise for analysis of surface integrity in turning and grinding operation. The stress state is analyzed in relation to tool wear. The results of measurements show that the residual stresses are not homogenous on the machined surface. This homogeneity depends on tool wear and stability of cutting process. Application of non-destructive testing through the Barkhausen noise is more suitable for grinding operations. Application of Barkhausen noise testing for turning operation will require the next research.

Keywords: Barkhausen noise, residual stress, grinding, turning

Published: December 1, 2010  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Ochodek V, Neslušan M, Rosípal M, Šípek M. Non-destructive analysis of surface integrity in turning and grinding operations. Manufacturing Technology. 2010;10(1):57-64. doi: 10.21062/ujep/x.2010/a/1213-2489/MT/10/1/57.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. NESLUŠAN, M. a kol. Experimentálne metódy v trieskovom obrábaní, EDIS Žilina, 2007, ISBN 978 - 80 - 8070 - 811 - 8, 349 s
    2. KARPUCHEWSKI, B. Introduction to micro magnetic techniques, ICBM1 report Hanover 2002
    3. ABUKU, S., CULLITY,R. D. A Magnetic Method for the Determination of residual Stress, Exp. Mech. 11,1971 Go to original source...
    4. ALTPETER, I.,THEINER, W., BECKER, R. Eigenspannungsmessung an stal deer Güte 22 NiMoCr 37 mit magnetischen und magnetoelastischen Prüfverfahren, 4th Intern.Conf.on NDE in Nuclear Industry, Lindau1981
    5. KINOSHITA, M., MURAYAMA, T., HOSHINA, N., KOBAYASHI, A., SHIMIZU, R., IKUTA, T. The surface damaged layer study of Mn-Zn single crystal ferrites using magnetic domain observation, CIRP, 1/1976, pp. 449
    6. THEINER, W., HÖLLER, P. Magnetishe Verfahren zur Spannungsermittlug, HTM - Beiheft Carl Hanser Verlag 1982
    7. BRINKSMEIER, E., SCHNEIDER, E. Nondestructive Testing for Evaluating Surface Integrity, CIRP, 2/1984, pp.489-496 Go to original source...
    8. THEINER, W.A., WILLEMS, H.H. Determination of Microstructural Parameters, Symposium on Nondestructive Methods for Material Property Determination, april 6-8, 1983 Hesrhey, Pennsylvania
    9. NESLUŠAN, M. Sústruženie kalených ocelí, Edis Žilina 2010, ISBN 978-80-554-104-1
    10. WANG, J.Y., LIU, C. R. The effect of Tool Flank Wear on the Heat Transfer, Thermal Damage and Cutting Mechanics in Finishing Hard Turning, CIRP Annals 48/1/1999, p. 53 - 56 Go to original source...
    11. BRANDT, D. Randzonenbeeinflussung beim Hartdrehen, Dr.-Ing. Dissertation, Universität-Hannover, 1995
    12. POKORNÝ, P., VÁCLAV, Š. Klasifikácia spôsobov rezania klinom. In: Vedecké práce MtF STU v Bratislave so sídlom v Trnave. - ISSN 1336-1589. - č. 25 (2008), s. 121-126
    13. WOJTAS, A. Analysis of residual stresses after shot peening. Strojírenská technologie, 2006, roč.XI.,č.3, s.6-9. ISSN 1211-4162.
    14. HOLEŠOVSKÝ, F. Stanovení zbytkových napětí v povrchu po obrábění. Strojírenská technologie, 2006, roč.XI.,č.3, s.29-32. ISSN 1211-4162.
    15. ŠTEKLÁČ, D., STANČEKOVÁ, D., ĎURECH, L., CZÁN, A. Zvyškové napätia při obránaní ložiskových materiálov a materiálov leteckých motorov. Strojírenská technologie, 2006, roč.XI., č.3, s.21-25. ISSN 1211-4162.

    Return to the content