Manufacturing Technology 2013, 13(2):241-247 | DOI: 10.21062/ujep/x.2013/a/1213-2489/MT/13/2/241

Polyurethane resins filled with inorganic waste particles

Petr Valášek, Miroslav Müller
Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences in Prague

Polyurethane resins belong to a group of polymers which can be easily filled with inorganic particles. Filling of the polymeric materials, either with particles or fibres, influences resulted properties of the arisen material - composite. The particle fillers can improve a wear resistance, they can optimize tensile characteristics and reduce the polymer price. The paper describes the polyurethane resin as a material recyclation bearer of the waste inorganic particles of the corundum, the artificial garnet and the silicon carbide. The experiment results certified that the mutual interaction of stated phases creates the wear resistant material which can be used owing to the polyurethane elasticity in the sphere of a cementing or at creating the material surface layers.

Keywords: abrasive wear, deformation, hardness, recyclation

Published: June 1, 2013  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Valášek P, Müller M. Polyurethane resins filled with inorganic waste particles. Manufacturing Technology. 2013;13(2):241-247. doi: 10.21062/ujep/x.2013/a/1213-2489/MT/13/2/241.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MLEZIVA, J., SNUPAREK J.(2000). Polymery výroba, struktura, vlastnosti a použití, 544 p. Sobotáles, Prague.
    2. EHRENSTEIN, G. W. (2009). Polymerní kompozitní materiály 1th ed., 351 p. Nakladatelství Scientia, Prague.
    3. LISKUTIN, P., MAZAL, P., et al. (2011). Modifikace kompozitu Al-Al2O3 malym množstvim Al2O3. Strojírenská technologie, No. 4, pp. 41 - 47.
    4. XIA JIA, XIAOMEI LING. (2005). Influence of Al2O3 reinforcement on the abrasive wear characteristic of Al2O3/PA1010 composite coatings. Wear. Vol. 258, No. 9, pp.1342 - 1347. Go to original source...
    5. SATAPATHY B.K., BIJWE, J. (2002). Analysis of simultaneous influence of operating variables on abrasive wear of phenolic composites. Wear, Vol. 253, pp. 787 - 794. Go to original source...
    6. MULLER, M., VALASEK, P. (2012). Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites. Manufacturing Technology, Vol. 12, pp. 55 - 59. Go to original source...
    7. KEJVAL, J., MÜLLER, M., HENC, P. (2012). Mechanické vlastnosti a "two-body" abrazívní opotřebení polymerních částicových kompozitů. Strojírenská technologie, Vol. 17, No. 1-2, pp. 33 - 38.
    8. OLEA-MEJIA O., BROSTOW W., BUCHMAN E. (2010). Wear Resistance and Wear Mechanisms in Polymer plus Metal Composites. Journal of nanoscience and nanotechnology. Vol. 10, pp. 8254 - 8259. Go to original source...
    9. KU, H., WONG, P. (2012). Contrast on Tensile and Flexural Properties of Glass Powder Reinforced Epoxy Composites: Pilot Study. Journal of applied polymer science, Vol. 123, pp.152 - 161. Go to original source...
    10. VALASEK, P., MULLER, M. (2012). Influence of bonded abrasive particles size on wear of polymeric particle composites based on waste. Manufacturing Technology, Vol. 12, No. 13, pp. 268 - 272. Go to original source...
    11. MULLER, M., VALASEK, P. (2010). Polymerní kompozity na bázi zpevňujících částic odpadů z procesu mechanické povrchové úpravy. Strojírenská technologie, Vol. 14, No. 0, pp. 183 - 186.
    12. NOVAK, M. (2011). Surface duality hardened steels after grinding. Manufacturing technology, Vol. 11, pp. 55 - 59. Go to original source...
    13. VALASEK, P., MULLER, M., CHOCHOLOUS, P. (2012). Polymerní částicové kompozity na bázi odpadu s obsahem oxidu křemičitého. Strojírenská technologie, Vol. 17, No. 1-2, pp. 122 - 127.
    14. VALASEK, P., MULLER, M. (2012). Polymeric particle composites with filler saturated matrix. Manufacturing Technology, Vol. 12, No. 13, pp. 272 - 276. Go to original source...
    15. BERTHELOT, J. M. (1999). Composite Materials - Mechanical Behavior and Structural Analysis. Mechanical engineering series. 635 p., Springer, New York. Go to original source...
    16. VALASEK, P., MÜLLER, M., KEJVAL, J. (2012). Faktory limitující použití polymerních částicových kompozitů - pórovitost. Strojírenská technologie, Vol. 17, Nr. 3, pp. 192 - 197.
    17. MULLER, M., PAVELKA, R. (2010). Jakost nátěrových systémů používaných v automobilovém průmyslu. Strojírenská technologie, Vol. 14, No. 0, pp. 187 - 190.

    Return to the content