Manufacturing Technology 2013, 13(4):428-431 | DOI: 10.21062/ujep/x.2013/a/1213-2489/MT/13/4/428

Studying of Cutting Zone When Finishing Titanium Alloy by Application of Multifunction Measuring System

Andrej Czán, Michal Sajgalík, Jozef Holubjak, Karel Kouril
University of Zilina, Faculty of Mechanical Engineering, Univerzitná 1, 010 26, ®ilina Slovakia, Slovak Republic

With the development of the automotive and aerospace industry and also biomedicine, exotic alloys are more and more used from all machined materials, especially titanium and nickel alloys, but which are hard-machined materials. Therefore it is necessary to know their behavior when machining, thoroughly. Processes occurring in the cutting zone when machining, are so complicated and dynamic, that their definition is carried out by certain specified models. Because the models have errors and deviations, it is needed to improve their observation so, that these deviations will manifest minimally or not. Based on the scientific research of the cutting zone, the multifunction measuring system was designed, which allows simultaneous measuring of components force of cutting, heat distribution and deformation processes in cutting zone during machining without its interruption.

Keywords: multifunction measuring system, cutting zone, high-speed movie, titanium alloys

Published: December 1, 2013  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Czán A, Sajgalík M, Holubjak J, Kouril K. Studying of Cutting Zone When Finishing Titanium Alloy by Application of Multifunction Measuring System. Manufacturing Technology. 2013;13(4):428-431. doi: 10.21062/ujep/x.2013/a/1213-2489/MT/13/4/428.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. CEP, R., KOURIL, K., MRKVICA, I., JANASEK, I., PROCHAZKA, J. (2010) Zkouąky nastroju Kyocera v podminkach prerusovaneho rezu. In. Strojirenska technologie, vol. XV, 2010/3, pp. 51-58, ISSN 1211-4162.
    2. CEP, R., JANASEK A., PETRU J., CEPOVA L., CZAN A., VALICEK J. (2013) Hard Machinable Machining of Cobalt-based Superalloy. In Manufacturing Technology XIII/13. UJEP: Ústi n. Labem. p. 226-231. ISSN 1213-2489 Go to original source...
    3. BREZNIČAN, M., FABIAN, P., MESKO, J., DRBUL, M., (2013) The Simulation of Influence of Quenching Temperature on Properties of Bearing Rings. In Manufacturing Technology XIII/13. UJEP: Ústi n. Labem. p. 20-25. ISSN 1213-2489 Go to original source...
    4. CZAN, A., TILLOVA, E., SEMCER, J., PILC, J. (2013) Surface and subsurface residual stresses after machining and their analysis by x-ray diffraction. In. Komunikacie, Volume 15, Issue 2, 2013, Pages 69-76. ISSN 1335-4205 Go to original source...
    5. HOLESOVSKY, F., NAPRSTKOVA, N., NOVAK, M., (2009) GICS for grinding process optimization. In Manufacturing Technology XII/12. 2012. UJEP: Ústi n. Labem. p. 22-26. ISSN 1213-2489. Go to original source...
    6. LUKOVICS, I., BILEK, O., HOLEMY, S. (2010) Aplikace sintrovaneho korundu ve vyrobe naradi. In. Strojirenska technologie XV - 2010/3, s - 27-34, ISSN 1211-4162.
    7. NOVAKOVA, J., PETRKOVSKA, L., BRYCHTA, J., STANCEKOVA, D. (2009). Influence of Cutting Parameters On Integrity Surface At High Speed Cuttin. Transactions of the V©B - Technical University of Ostrava. Mechanical Series, ročník LV., číslo 1/2009, Česká republika. Ostrava: V©B - TUO, pp. 203-209
    8. PILC, J., VASILKO, K. (2013) Development and applications of a rotating turning tool. In Manufacturing Technology XIII/13. UJEP: Ústi n. Labem. p. 226-231. Go to original source...
    9. SAJGALIK M., CZAN A., (2011) Studying of processes in cutting zone by non-destructive methods, volume 8, number 2 of Technological Engineering, University of Zilina in Zilina.
    10. SAJGALIK M., STANCEKOVA D., JURKY M., KURNAVA P. (2012) Application of thermovision systems and highspeed scanning for monitoring of dynamic processes in the cutting zone in turning of superalloys, volume 6 of Advanced manufacturing technologies
    11. MRKVICA, I., JANO©, M., SYSEL, P. (2012) Contribution to milling of materials on Ni base. In Applied Mechanics and Materials 217-219, pp. 2056-2059. ISSN: 1660-9336 Go to original source...
    12. WHITENTON E.P., IVESTER R., et al. (2005) Simultaneous visible and thermal imaging of metals during machining in Thermosense XXVII. Orlando, International Society for Optical Engineering. Go to original source...
    13. WHITENTON, E.P. (2010) High-speed dual spectrum imaging for the measurement of metal cutting temperatures, Manufacturing Engineering Laboratory, NIST, Gaithersburg Go to original source...
    14. CEP, R., JANASEK, A., CEPOVA, L., PETRU, J., HLAVATY, I., CAR, Z., HATALA, M. (2013) Eksperimentalno ispitivanje rezne sposobnosti izmjenjivih reznih umetaka | [Experimental testing of exchangeable cutting inserts cutting ability]. In Tehnicki Vjesnik 20 (1), pp. 21-26. ISSN: 1330-3651
    15. MOHYLA, P., TOMCIK, P., BENES, L., HLAVATY, I. (2011)Effect of post-welding heat treatment on secondary hardening of welded joints of Cr-Mo-v steel. Metal Science and Heat Treatment 53 (7-8), pp. 374-378. ISSN: 0026-0673. Go to original source...

    Return to the content