Manufacturing Technology 2014, 14(1):30-36 | DOI: 10.21062/ujep/x.2014/a/1213-2489/MT/14/1/30

The Powdered Magnets Technology Improvement by Biencapsulation Method and its Effect on Mechanical Properties

Dorota Klimecka-Tatar
Institute of Production Engineering, Faculty of Management, Częstochowa Univesity of Technology, Armii Krajowej 19B, 42-201 Czestochowa, Poland

In this paper the technological process of bonded magnets manufacturing was described. The greatest dangers arising during the process steps that have a significant impact on magnetic, chemical and thermodynamic stability Nd-Fe-B bonded type of magnetic materials were also indicated. The effect of the biencapsulation of Nd12Fe77Co5B6 powder particles with Ni-P/epoxy resin, phosphate/epoxy resin and Cu/epoxy resin layers on the finale magnets has been evaluated. The production processes in technological terms in original and after improving modification were presented - the technological process taking into account the stage of powder surface etching and the powder particles biencapsulation. It was proved that the preliminary biencapsulation of particles surface before consolidation in some cases significantly improve the mechanical properties of the bonded with epoxy-resin magnets.

Keywords: bonded magnets, biencapsulation, Nd-Fe-B magnets, magnetic composites

Published: March 1, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Klimecka-Tatar D. The Powdered Magnets Technology Improvement by Biencapsulation Method and its Effect on Mechanical Properties. Manufacturing Technology. 2014;14(1):30-36. doi: 10.21062/ujep/x.2014/a/1213-2489/MT/14/1/30.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. BALA H., SZYMURA S. (1995) Inż. Materiałowa, 3, pp.119.
    2. BALA H., TREPAK N.M., SZYMURA S., LUKIN A.A., GAUDYN V.A., ISAICHEVA L.A., PAWŁOWSKA G., ILINA L.A. (2001). Intermetallics, 9, pp. 515. Go to original source...
    3. DIAN M. (2013). The Methodology of Quality Matrix in Manufacturing Quality Process Improvement. Manufacturing Technology. Vol. 13, No. 4, pp. 431-437. Go to original source...
    4. DOBRZAŃSKI L.A., DRAK M., TRZASKA J. (2005). J.Mater.Proc.Tech., 164, pp. 795 Go to original source...
    5. EDGLEY D. S., LE BRETON J.M., STEYAERT S., AHMED F.M., HARRIS I.R., TEILLET J. (1997) J.Magn.Magn.Mater., 173, pp. 29. Go to original source...
    6. EL-MONEIMA A.A., GEBERT A., SCHNEIDER F., GUTFLEISH O., SHULTZ F. (2002), Corros.Sci. 44, pp. 1097. Go to original source...
    7. EL-MONEIMA A.A., GUTFLEISH O., PLOTNIKOV A., GEBERT A. (2002). J.Magn.Magn. Mater., 248, pp. 121. Go to original source...
    8. HARI KRISHNAN K, JOHN S, SRINIVASAN KN, PRAVEEN J, GANESAN M, KAVIMANI PM (2006) Metall Mater. Trans A 37. pp. 1917-1926. Go to original source...
    9. KLIMECKA-TATAR D, ¦LUSAREK B, BALA H, GĘSIARZ K (2005) Ochr Przed Koroz 11s/A, pp. 93-97.
    10. KLIMECKA-TATAR D, BALA H, ¦LUSAREK B, JAGIELSKA-WIADEREK K. (2009) Arch Metall Mater 54/1, pp. 247-256.
    11. KLIMECKA-TATAR D. (2011). The Production Process of Bonded Magnets Based on Microencapsulated Nd14.8Fe76Co4.95B4.25 Powder. Chapter 10. In:Toyotarity. Heijunka. Monography. Editing and Scientific Elaboration Stanisław Borkowski, Robert Ulewicz s.155-170 Dnipropetrovsk
    12. KLIMECKA-TATAR D, PAWŁOWSKA G, RADOMSKA K (2013) Ochr Przed Koroz, 56/5, pp. 187-190.
    13. PAWŁOWSKA G, KLIMECKA-TATAR D, MAZIK A (2013) Ochr Przed Koroz 56/4, pp. 174-176.
    14. KORDAS K, BEKESI J, VAJTAI R, NANAI L, LEPPAVUORI S, UUSIMAKI A, BALI K, GEORGE TF, GALBACS G, IGNACZ F, MOILANEN P (2001) Appl Surf Sci 172, pp. 178-189.
    15. LEONOWICZ M., WOJCIECHOWSKI S. (1988) Archiwum Nauki o Materiałach, 9, pp. 263.
    16. LEONOWICZ M., WYSŁOCKI J.J. (2005). Współczesne magnesy, WNT, Warszawa.
    17. MAREK I., MICHALCOVA A., VOJTECH D. (2013). Properties of metallic nanocrystalline powders. Manufacturing Technology, Vol. 13, No. 3, pp. 353 - 358. Go to original source...
    18. RADA M., LYUBINA J., GEBERT A., GUTFLEISCH O., SCHULTZ L. (2005) J.Magn.Magn. Mater., 290, pp. 1251 Go to original source...
    19. ¦LUSAREK B. (2001). Dielektromagnets Nd-Fe-B, Oficyna Wyd. Politechniki Wrocławskiej, Wrocław.
    20. SKULJ I., DOUVALIS A.P., HARRIS I.R. (2006). J.Alloy.Compd, 407, pp. 304 Go to original source...
    21. ULEWICZ R. (2003). Quality control system in production of the castings from spheroid cast iron, Metalurgija Vol. 42, Issue 1, pp. 61-63.
    22. VALÁ©EK P., MÜLLER M. (2013). Polyurethane resins filled with inorganic waste particles. Manufacturing Technology. Vol. 13, No. 2, pp. 241-247. Go to original source...
    23. XIAO J., OTAIGBE J. (2000), J.Alloy.Compd, 309, pp. 100. Go to original source...

    Return to the content