Manufacturing Technology 2014, 14(1):56-60 | DOI: 10.21062/ujep/x.2014/a/1213-2489/MT/14/1/56

Evaluation of Mechanical Properties of Samples Printed by FDM Method

Miloslav Linda1, Miroslav Müller2, Rostislav Chotìborskı2
1 Faculty of Engineering, Department of Electrical Engineering and Automation, Czech University of Life Sciences in Prague. Kamıcka 129, 165 21 Praha - Suchdol. Czech Republic
2 Faculty of Engineering, Department of Material Science and Manufacturing Technology, Czech University of Life Sciences in Prague. Kamıcka 129, 165 21 Praha - Suchdol. Czech Republic

To ensure optimal conditions of instruction in technical subjects it is fundamental to have laboratory trainings where students learn methods of the material measuring and they get pieces of knowledge about a test equipment. Financial cost of samples leads to minimizing laboratory trainings. It can be solved by fused deposition modelling (FDM). The aim of the research was to test a possibility to use test samples made by means of FDM method for an implementation within the practical training. Within the research two standard materials determined for FDM (that means ABS plastic and PLA) were used. Test samples were made / printed by a printer EASY3DMAKER with using a software G3DMAKER. Test of an abrasive wear, a hardness Shore D measurement, a tensile strength and an impact strength were performed for verifying a functionality of the test samples printed by FDM method for laboratory experiments.

Keywords: laboratory training, testing, research, fused deposition modeling

Published: March 1, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Linda M, Müller M, Chotìborskı R. Evaluation of Mechanical Properties of Samples Printed by FDM Method. Manufacturing Technology. 2014;14(1):56-60. doi: 10.21062/ujep/x.2014/a/1213-2489/MT/14/1/56.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. NÁPRSTKOVÁ, N. (2011). Using of Catia V5 Software for Teaching at Faculty of Production Technology and Management. In: Proceedings from 10th International Scientific Conference Engineering for Rural Development, Volume 10, pp. 554-557, Jelgava, Latvia University of Agriculture, Faculty of Engineering.
    2. NÁPRSTKOVÁ, N., NÁPRSTEK, V., HOLE©OVSKİ, F. (2008). Nettings of Students to the Grinding Process Monitoring, In: Engineering for Rural Development, pp. 296-299, Latvia University of Agriculture Faculty of Engineering.
    3. NOVAK-MARCINCIN, J., FECOVA, V., BARNA, J., JANAK, M., NOVAKOVA-MARCINCINOVA, L. (2013). Using of the Virtual Reality Application with the Scanning Device Kinect for Manufacturing Processes Planning, In: Manufacturing technology, Vol. 13. No. 2 pp. 215 - 219. Go to original source...
    4. MÜLLER, M., VALÁ©EK, P. (2012). Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites, In. Manufacturing technology, Vol. 12, No. 12, pp. 55 - 59. Go to original source...
    5. NOVÁK, M. (2012). Surfaces with high precision of roughness after grinding. In: Manufacturing technology, Vol. 12, No.12, pp. 66-70. Go to original source...
    6. NOVÁK, M. (2011). Surface quality of hardened steels after grinding. In: Manufacturing technology, Vol. 11, No. 11, pp. 55 - 59. Go to original source...
    7. NESLU©AN, M., ROSIPAL, M., KOLAØIK, K., OCHODEK, V. (2012). Application of barkhausen noise for analysis of surface integrity after hard turning. In: Manufacturing technology, vol. 12, no. 11, pp. 60 - 65. Go to original source...
    8. HOLE©OVSKİ, F., NÁPRSTKOVÁ, N., NOVÁK, M. (2012). GICS for grinding process optimization, In: Manufacturing technology, Vol. 12, No. 11, pp. 22 - 26. Go to original source...
    9. ÈSN 62 1466: 1993. Rubber, determination of abrasion resistance using a rotating cylindrical drum device. Prague: Federal office for standard and measuring, 1993.12 p.
    10. MÜLLER, M., VALÁ©EK, P. (2012). Abrasive wear effect on Polyethylene, Polyamide 6 and polymeric particle composites, In: Manufacturing technology, Vol. 12, No. 12, pp. 55 - 59. Go to original source...
    11. ÈSN EN ISO 868: 2003. Plastics and ebonite - Determination of indentation hardness by means of durometr (Shore hardness). Czech Standard Institution, Prague, 2003. 10 p.
    12. ÈSN EN ISO 3167 (1997): Plastics - Multipurpose test specimens. Czech Standard Institute, Prague.
    13. ÈSN EN ISO 527-1 (1997): Plastics - Determination of tensile properties - Part 1: General principles. Czech Standard Institute, Prague.
    14. VALÁ©EK, P., MÜLLER, M. (2013). Polymeric composite based on glass powder - usage possibilities in agrocomplex. In: Scientia Agriculturae Bohemica, Vol. 44, No. 2, pp. 107 - 112. Go to original source...
    15. VALÁ©EK, P., MÜLLER, M. (2013). Composite based on hard-cast irons utilized on functional areas of tools in agrocomplex. In: Scientia Agriculturae Bohemica, Vol. 44, No. 3, pp. 172 - 177. Go to original source...

    Return to the content