Manufacturing Technology 2016, 16(5):1063-1067 | DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/1063

Analysis of the Composition of Selected Inserts Using Electron Microscopy

Nataša Náprstková1, Jaromír Cais1, Dana Stančeková2, Pavel Kraus1
1 Faculty of Production Technology and Management, J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7, 400 01 Usti nad Labem. Czech Republic
2 Faculty of Mechanical Engineering, University of Žilina, Veľký diel, 010 26 Zilina, Slovak Republic

Using of cutting inserts is currently a normal part of the manufacturing process. The article deals with structural analysis and material selection of inserts for turning. Analysis of the composition of experimental inserts was made by electron microscopy, namely EDS analysis. EDS analysis is an analysis using an energy dispersive spectrometer. For this purpose was used EDS analyzer Bruker 16 which is part of a scanning electron microscope Tescan Vega 3. These analysis can provide a good picture of the structure and construction of inserts and their composition. This may assist in finding suitable cutting conditions. These analyzes were performed in other experiments performed at the Faculty of Production Technology and Management at Jan Evangelista Purkyně University in Ústí nad Labem.

Keywords: The cutting insert, chemical composition analysis, EDS

Published: October 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Náprstková N, Cais J, Stančeková D, Kraus P. Analysis of the Composition of Selected Inserts Using Electron Microscopy. Manufacturing Technology. 2016;16(5):1063-1067. doi: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/1063.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. CAIS, J. (2015). Elektronova mikroskopie. Metalografie, Praha, CZ.1.07/2.3.00/45.00 29, ISBN 978-80-86302-67-6 [online], 2015 [cit. 14. 5. 2016]. Available from <http://www.csvs.cz/projekty/2014_veda_pro_zivot/data/11_KA3_Jaromir_Cais_2_Elektronova_%20mikroskopie_a_%20EDS_%20analyza_metodicka_prirucka.pdf>
    2. WEISS, V., SVOBODOVA, J. (2015). The Use of Colour Metallography and EDS for Identification of Chemical Heterogeneity of Selected Aluminium Alloys Copper and Zinc Alloyed. In: Manufacturing Technology, Vol. 15, No. 6, pp. 1048-1053. Czech Republic Go to original source...
    3. CZAJKOWSKA, A., KOSSAKOWSKI, P., WCIŚLIK, W., STASIAK-BETLEJEWSKA, R. (2013). Application of Electron Scanning Microscope in the Analysis of the Structure of Casting NonConformities Aimed at Optimization of Technological Process Parameters. In: Manufacturing Technology, Vol. 13, No. 2, pp. 164-169. Czech Republic Go to original source...
    4. Bruker Q4 TASMAN - the "Multi-Tool" in Metal Analysis [online], 2016 [cit. 3. 5. 2016]. Available from <http://trends.directindustry.com/bruker-elemental-gmbh/project-30028-124882.html>
    5. PETRU, J., ZLAMAL, T., MRKVICA, I., CEP, R. (2014). The Effect of Thermal Shocks on Wear of Exchangeable Sintered Carbide Inserts during the Cutting Process. In: Manufacturing Technology, Vol. 14, No. 4, pp. 590-596. Czech Republic Go to original source...
    6. HUMÁR. A. (2008) Materialy pro rezne nastroje. MM Publishing, s.r.o., Prague, Czech Republic
    7. KORDIK, M., STRUHARNANSKY, J., MARTIKAN, A., STANCEKOVA, D., KUSMIERCZAK, S., MARTINCEK, J. (2016) Inserts Coating Influence on Residual Stress of Turned Outer Bearings. In: Manufacturing Technology, Vol. 16, No. 1, pp. 132-136. Czech Republic Go to original source...
    8. SVOBODOVA, J. (2014) SEM and EDS Analysis Used in Evaluation of Chemical Pre-treatment Based on Nanotechnology. In: Manufacturing Technology, Vol.14, No.3, pp. 461-467. Czech Republic Go to original source...
    9. SNAHNICAN, F. (2015). Deposition of Aluminium Oxide (Al2O3) Coatings on Aluminium Substrate Using Anodizing Processes. In: Manufacturing Technology, Vol 15, No 3, pp. 423-428. Czech Republic Go to original source...
    10. KUSMIERCZAK, S. (2011). The Usage of Confocal Laser Microscope by Solving Students Projects, In: proceedings of International Miltidisciplinary Conference, 2011, Nyíregyháza, Hungary, pp.149-152
    11. MICHNA, S., KUSMIERCZAK, S. (2012). Praktická metalografie. 245 pp., UJEP, Usti nad Labem, Czech Republic.
    12. TAVODOVA, M. Moznosti inovacii vyucby strojarskych technologii. In: Proceedings Zvysovani efektivnosti vzdelavacieho procesu prostrednictvom inovacnych prostriedkov, pp. 81-85. TU vo Zvolene, Zvolen, Slovakia.
    13. PETRU, J., SCHIFFNER, J., ZLAMAL, T., SADILEK, M., STANCEKOVA, D. (2015). Investigations of Cutting Tool Wear While Machining Inconel 718. In: Manufacturing Technology, Vol 15, No 3, pp. 396-403. Czech Republic. Go to original source...
    14. VALASEK, P. MÜLLER, M. (2014). Picture Analysis of Failure Areas of Particle Composites. In: Manufacturing Technology Vol 14, No 3, pp. 474-478. Czech Republic Go to original source...
    15. WEISS, V. (2012). Hodnoceni vlivu teploty a doby homogenizačniho žihani slitiny AlCu4MgMnz hlediska mikrostruktury, obrazove analyzy a metody EDX. In: Strojirenska technologie, Vol. 17, No. 5,6, p. 348-355. Czech Republic.

    Return to the content