Manufacturing Technology 2016, 16(5):1078-1085 | DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/1078

Influence of Chemical Composition of Selected Materials on the Roughness of Cutting Edge and the Width of HAZ

Rastislav Nigrovič1, Jozef Meško1, Dušan Arsić2, Vukić Lazić2, Ružica Nikolić2,3
1 University of Zilina, Univerzitná 1, Department of Technological Engineering
2 Faculty of Engineering, University of Kragujevac, Sestre Janijić 6, Str., 34000 Kragujevac, Serbia
3 Research centre, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia

The presented article deals with the technology and principals of laser cutting. The article describes the properties of CO2 laser beam, input parameters of laser cutting process, assist gases, the interaction of the cut material and the stability of laser cutting. The chemical compositions of cut materials and their influence on the cutting properties focusing on the roughness of the surface, are described as well. In the experimental part the roughness of the surface was measured by using the 3D scanning and evaluation of the microstructure in the HAZ area was provided.

Keywords: Laser cutting, HAZ width, Roughness

Published: October 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Nigrovič R, Meško J, Arsić D, Lazić V, Nikolić R. Influence of Chemical Composition of Selected Materials on the Roughness of Cutting Edge and the Width of HAZ. Manufacturing Technology. 2016;16(5):1078-1085. doi: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/1078.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. SILVFAST, W. T. (2004). Laser Fundamentals, Cambridge University Press, 666p. ISBN 0-521-83345-0. Go to original source...
    2. CARISTAN, L. C. (2004). Laser cutting guide for manufacturing. Dearborn, Michigan, USA: Society of Manufacturing Engineers, 452p. ISBN 0-87263-686-0.
    3. KONAR, R., PATEK, M., ZRAK, A.(2015) Ultrasonic testing of non-ferrous materials in the foundry industry. In: Manufacturing Technology: journal for science, research and production, Vol. 15, No. 4, s. 557-562. ISSN 1213-2489. Go to original source...
    4. ZRAK, A., KONAR, R., JANKEJECH, P. (2015). Influence of chemical composition in steel on laser cutting stability. In: Manufacturing Technology: journal for science, research and production, Vol. 15, No. 4, s. 748-752. ISSN 1213-2489. Go to original source...
    5. KONAR, R., MICIAN, M., HLAVATY, I. (2014). Defect detection in pipelines during operation using Magnetic Flux Leakage and Phased Array ultrasonic method. In: Manufacturing technology, Vol. 14, No. 3, pp. 337-341. J.E. Purkyne University, Ústi nad Labem. ISSN 1213-2489. Go to original source...
    6. KONAR, R., MICIAN, M. (2014). Non-destructive testing of welds in gas pipelines repairs with Phased Array ultrasonic technique. In: Manufacturing technology, Vol. 14, No. 1, pp. 42-47. J.E. Purkyne University, Ústi nad Labem. ISSN 1213-2489. Go to original source...
    7. MESKO, J., ZRAK, A., MULCZYK, K., TOFIL, S. (2014). Microstructure analysis of welded joints after laser welding. In: Manufacturing technology, Vol. 14. No. 3, pp. 355-359. 341. J.E. Purkyne University, Ústi nad Labem. ISSN 1213-2489. Go to original source...
    8. PATEK, M., KONAR, R., SLADEK, A., RADEK, N. (2014). Non-destructive testing of split sleeve welds by the ultrasonic TOFD method. In: Manufacturing technology, Vol. 14, No. 3, pp. 355-359. J.E. Purkyne University, Ústi nad Labem. ISSN 1213-2489. Go to original source...
    9. LAGO, J., GUAGLIANO, M., NOVY, F., BOKUVKA, O., (2016). Influence of laser shock peening surface treatment on fatigue endurance of welded joints from S355 structural steel. In: Manufacturing technology: journal for science, research and production. Vol. 16, No. 1, pp. 154-159. ISSN 1213-2489. Go to original source...
    10. ZAPOMĚL, J., DEKÝŠ, V., FERFECKI, P., SAPIETOVÁ, A., SÁGA, M., ŽMINDÁK, M. (2015). Identification of Material Damping of a Carbon Composite Bar and Study of Its Effect on Attenuation of Its Transient Lateral Vibrations. In: International Journal of Applied Mechanics, Vol. 7, No. 6, (2015)1550081 (18 pages). DOI: 10.1142/S1758825115500817. Go to original source...
    11. DANIELEWSKI, H., BANAK, R., DOMAGALA, A. (2013). The Experimental Analysis of Striation Pattern Created During Laser Cutting. In: Transcom 2013, Žilina, Slovakia.
    12. SKOCOVSKY, P., BOKUVKA, O., KONECNA, R., TILLOVA, E. (2006). Náuka o materiáli pre odbory strojnícke, EDIS vydavateľstvo ŽU, 349s. ISBN 80-8070-593-3
    13. SEJC, P., BELIAK, R., SVEC, P., ROSKO, M. (2006). Computer simulation of heat affected zone during MIG brazing of zinc - coated steel sheets. In: Kovové materiály. Metallic materials. Roč. 44, č. 4. s. 225-234, ISSN 0023-432x

    Return to the content