Manufacturing Technology 2017, 17(5):778-782 | DOI: 10.21062/ujep/x.2017/a/1213-2489/MT/17/5/778

Possibilities for Change of Thermoplastic Tensile Properties Using Admixture of Recyclable Material

Ján Majerník, Ján Kmec, Monika Karková, Martin Podařil
Institute of Technology and Business in České Budějovice, Okružní 517/10, 370 014 České Budějovice, Czech Republic

Polymeric materials are thanks its processing and utility properties materials in demand of common and special use. They are also largely replacing conventional materials. As the popularity of polymeric materials grows, also the amount of its waste increases. For this reason, there is introduced the term recycling as a method of processing, re-use of the waste, into technologies of polymeric processing. So, this paper deals with the possibilities of introduction of recycled material. The main part of this paper is created by an experiment that explores the changes of tensile properties of test specimen according to the selected percentage of additives in the volume of the basic granulate. The test specimen was produced by mixing pure granules with the addition of recycled and re-granulated materials. The conclusion of this work presents a comparison of the results of each tensile test that provide an overview of the behaviour and properties of the materials tested.

Keywords: thermoplastic, recycled material, tensile test

Published: October 1, 2017  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Majerník J, Kmec J, Karková M, Podařil M. Possibilities for Change of Thermoplastic Tensile Properties Using Admixture of Recyclable Material. Manufacturing Technology. 2017;17(5):778-782. doi: 10.21062/ujep/x.2017/a/1213-2489/MT/17/5/778.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. STN EN ISO 294-1. Plasty. Vstrekovanie skúšobných telies z termoplastových materiálov. Časť 1: Všeobecné princípy a vstrekovanie viacúčelových a tyčinkových skúšobných telies. Bratislava: Slovenský ústav technickej normalizácie, 2001. 20 p.
    2. STN EN ISO 527-1. Plasty. Stanovenie ťahových vlastností. Časť 1: Všeobecné zásady. Bratislava: Slovenský ústav technickej normalizácie, 2012.
    3. STN EN ISO 527-2. Plasty. Stanovenie ťahových vlastností. Časť 2: Skúšobné podmienky pre lisované a vytláčané plasty. Bratislava: Slovenský ústav technickej normalizácie, 2012.
    4. RAZ, K., ZAHALKA, M., CHVAL, Z. (2017). Injection Molding Quality Improvement by Advanced Virtual Simulations. MANUFACTURING TECHNOLOGY, 2017, vol. 17, no. 1, p. 79-83. ISSN 1213-2489. Go to original source...
    5. DVORAK, Z., HNATKOVA, E., SEDLACIK, M. (2016). Mold Surface Contamination during Polymer Processing. MANUFACTURING TECHNOLOGY, 2016, vol. 16, no. 1, p. 63-69. ISSN 1213-2489. Go to original source...
    6. NIGROVIČ, R., MEŠKO, J. (2016). Laser Cutting of Non-Metallic Material - PMMA. MANUFACTURING TECHNOLOGY, 2016, vol. 16, no. 2, p. 402-406. ISSN 1213-2489. Go to original source...
    7. RAGAN, E., RUŽBARSKÝ, J., MAŇAS, M., et al. (2008). Vstrekovanie a spracovanie plastických hmôt. 1st ed. Prešov: Fakulta výrobných technológií si sídlom v Prešove, 2008. 548 p. ISBN 978-80-7300-250-3
    8. GREŠKOVIČ, F., DULEBOVÁ, Ľ., VARGA, J. (2010). Technológie spracovania plastov: Vstrekovanie. 1st ed. Košice: Strojnícka fakulta TUKE, 2010. 200 p. ISBN 978-80-553-0369-7.
    9. VALÁŠEK, P., MÜLLER, M. (2012). Polymeric particle composites with filler saturated matrix. MANUFACTURING TECHNOLOGY, 2012, vol. 12, no. 13, p. 272-276. ISSN 1213-2489. Go to original source...
    10. VALÁŠEK, P., MÜLLER, M. (2013). Changes of Polyurethane Mechanical Properties Filled with Glass Powder. MANUFACTURING TECHNOLOGY, 2013, vol. 13, no. 4, p. 563-568. ISSN 1213-2489. Go to original source...

    Return to the content