Manufacturing Technology 2017, 17(6):930-935 | DOI: 10.21062/ujep/x.2017/a/1213-2489/MT/17/6/930

The Impact of Technological Parameters on Casting Integrity and Mechanical Properties of AlSi7Mg0.3 Alloy by Using Squeeze Casting Technology

Richard Pastircak, Jan Scury, Tomas Fecura
Department of Technological Engineering, Faculty of Mechanical Engineering, University of ®ilina. Univerzitná 8215/1, 010 26 ®ilina. Slovak Republic

The article deals with the effect of variaton of the technological parameters on the change mechanical properties and density of the AlSi7Mg0.3 alloy using squeeze casting technology. The AlSi7Mg0.3 alloy has been chosen because the acting pressure has the most significant impact on Al-Si alloys. For the make a samples was used a direct squeeze casting technology. Differently casting temperatures and mold temperatures at the acting pressure of 30 MPa were varied for individual samples. From the mechanical properties was specifically evaluated tensile strength and elongation.

Keywords: Squeeze Casting, Al-Si Alloys, Mechanical Properties, Casting Integrity

Published: December 1, 2017  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Pastircak R, Scury J, Fecura T. The Impact of Technological Parameters on Casting Integrity and Mechanical Properties of AlSi7Mg0.3 Alloy by Using Squeeze Casting Technology. Manufacturing Technology. 2017;17(6):930-935. doi: 10.21062/ujep/x.2017/a/1213-2489/MT/17/6/930.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. PASTIRČÁK, R., ©ČURY, J., BRŮNA, M., BOLIBRUCHOVÁ, D. (2017). Effect of Technological Parameters on the AlSi12 Alloy Microstructure During Crystallization Under Pressure. In: Archives of foundry engineering, ISSN 1897-3310, Vol. 17, No. 2, pp. 75 - 78. Go to original source...
    2. PASTIRČÁK, R., ©ČURY, J. (2016). Effect of technological parameters on microstructure in alloy AlCu4Ti using squeeze casting. In: American Institute of Physics Publising. ISSN 0094-243X, AIP conference proceedings, vol. 1745. Go to original source...
    3. AWEDA, J.O., ADEYEMI, M. B. (2009). Experimental determination of heat transfer coefficients during squeeze casting of aluminium. In: Journal of Materials Processing Technology, No. 3, pp. 1477 - 1483. Go to original source...
    4. LEE, J. H., KIM, H. S., WON, C. W., CANTOR, B. (2002). Effect of the gap distance on the cooling behavior and the microstructure of indirect squeeze cast and gravity die cast 5083 wrought Al alloy. In: Materials Science & Engineering A, Vol. 338, No. (1-2), pp. 182 - 190. Go to original source...
    5. BRŮNA, M., KUCHARČÍK, L. (2013). Prediction of the Porosity of Al Alloys. In: Manufacturing Technology, ISSN 1213-2489, Vol. 13, No. 3, pp. 296 - 302. Go to original source...
    6. PODPROCKÁ, R., MALIK, J., BOLIBRUCHOVÁ, D. (2015). Defects in High Pressure Die Casting Process. In: Manufacturing technology, ISSN 1213-2489, Vol. 15, No. 4, pp. 674 - 678. Go to original source...
    7. NOVÁ, I., MACHUTA, J. (2013). Squeeze casting results of aluminium alloys. In: Manufacturing technology, ISSN 1213-2489, Vol. 13, No. 1, pp. 73 - 79. Go to original source...
    8. BOLIBRUCHOVA, D., RICHTARECH, L., DOBOSZ, S. M., MAJOR-GABRYS, K. (2008). Utilisation of Mould Temperature Change in Eliminating the Al5FeSI Phases in Secondary AlSi7Mg0.3 Alloy. In: Archives of Metallurgy and Materials, ISSN 1733-3490, 2017, Vol. 62, No. 1, pp. 357 - 362. Go to original source...
    9. BOLIBRUCHOVA, D., MACKO, J., BRUNA, M. (2014). Elimination of negative effect of Fe in secondary alloys AlSi6Cu4 (EN AC 45 000, A 319) by nickel. In: Archives of metallurgy and materials, ISSN 1733-3490, Vol. 59, No. 2, pp. 717 - 721. Go to original source...
    10. BRŮNA, M., SLÁDEK, A. (2016). Hot tearing evaluation of Al - based alloys. Manufacturing technology, ISSN 1213-2489, Vol. 16, no. 2 (2016), pp. 323-327. Go to original source...
    11. TILLOVA, E., CHALUPOVA, M., KUCHARIKOVA, L., ZAVODSKA, D., BELAN, J., VASKO, A. (2016) Use of Microscopy in the Study of Self-Hardening Al-Alloy for Automotive Application. In: Manufacturing technology, ISSN 1213-2489, Vol. 16, No. 5, pp. 1174-1179. Go to original source...

    Return to the content