Manufacturing Technology 2018, 18(1):66-71 | DOI: 10.21062/ujep/55.2018/a/1213-2489/MT/18/1/66

Experimental Investigation and Measurement of Surface Roughness and Cutting Forces while Turning AlCu3MgMnPb Aluminium Alloy

Jozef Majerík1, Rozmarína Dubovská2, Ivan Baška1, Jaroslav Jambor1
1 Faculty of Special Technology Alexander Dubcek University of Trencin. Pri Parku 19, 911 5 Trenčín. Slovak Republic
2 Faculty of Education University of Hradec Kralove. Rokitanskeho 62, 500 03 Hradec Králové Czech Republic

The main aim of this scientific article is to assess the contribution of surface layers by determining the experimental investigation and practical measurement of surface roughness Ra and selected components of cutting forces while external turning of AlCu3MgMnPb aluminium alloy. In these experimental procedures, a number of turning tests have been carried out by using a universal lathe machine tool and cutting forces and surface roughness scientific measuring devices. These realized measurements have been successively investigated and experimentally verified with the prepared trial samples. These presented experimental measurements describes the authors investigation of cutting forces while turning by the piezoelectric dynamometer Kistler type 5001 and surface roughness Ra with the Talysurf CLI 100 measuring device. This scientific article, together with measured and calculated results, is the fundamental that will help to optimizing the quality and used other technological and cutting parameters of turning technological process.

Keywords: Surface Roughness, Tangential Cutting Force, Axial Cutting Force, Dynamometer, Aluminium Alloy

Published: February 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Majerík J, Dubovská R, Baška I, Jambor J. Experimental Investigation and Measurement of Surface Roughness and Cutting Forces while Turning AlCu3MgMnPb Aluminium Alloy. Manufacturing Technology. 2018;18(1):66-71. doi: 10.21062/ujep/55.2018/a/1213-2489/MT/18/1/66.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. VIPINDAS, K., KURIACHEN, B., MATHEW, J. (2016). Multi-regression prediction model for surface roughness and tool wear in turning novel aluminium alloy (LM6)/fly ash composite using response surface and central composite design methodology. In: International Journal of Advanced Manufacturing Technology, Article in Press, pp. 1 - 6. Springer. Go to original source...
    2. ÇAKIR, A., YAĞMUR, S., KAVAK, N., KÜÇÜKTÜRK, G., ŞEKER, U. (2016). The effect of minimum quantity lubrication under different parameters in the turning of AA7075 and AA2024 aluminium alloys. In: International Journal of Advanced Manufacturing Technology, Vol. 84, No. 9-12, pp. 2515 - 2521. Springer. Go to original source...
    3. TORRES, A., PUERTAS, I., LUIS, C. J. (2015). Surface Roughness Analysis on the Dry Turning of an Al-Cu Alloy. In: Procedia Engineering, Vol. 132, pp. 537 - 544. Elsevier BV. Go to original source...
    4. QU, S., SUN, F., ZHANG, L., LI, X. (2014). Effects of cutting parameters on dry cutting of aluminium bronze alloy. In: International Journal of Advanced Manufacturing Technology, Vol. 70, No. 1-4, pp. 669 - 678. Springer. Go to original source...
    5. YUSUF, M., ARIFFIN, M. K. A., ISMAIL, N., SULAIMAN, S. (2013). Chip formation and surface roughness in dry machining of aluminium alloys. In: Advanced Science Letters, Vol. 19, No. 8, pp. 2343 - 2346. Go to original source...
    6. BHUSHAN, R. K., KUMAR, S., DAS, S. (2010). Effect of machining parameters on surface roughness and tool wear for 7075 Al alloy SiC composite. In: International Journal of Advanced Manufacturing Technology, Vol. 50, No. 5-8, pp. 459 - 469. Springer. Go to original source...
    7. DUBOVSKÁ, R., MAJERÍK, J. (2015). Experimental investigation and analysis of cutting forces when machining of X5CrNi18-10 stainless steel. In: Manufacturing Technology, Vol. 15, No. 3, pp. 322 - 329. Go to original source...
    8. DUBOVSKÁ, R., MAJERÍK, J., CHOCHLÍKOVÁ, H. (2014). Cutting forces numerical analysis and research of dry turning of 1.4301 with wiper coated carbide insert. In: Applied Mechanics and Materials, Vol. 528, pp. 34 - 43. TTP. Switzerland. Go to original source...
    9. DUBOVSKÁ, R., JAMBOR, J., MAJERÍK, J. (2014). Qualitative aspects of machined surfaces of high strength steels. In: Procedia Engineering, Vol. 69, pp. 646 - 654. Elsevier BV. Go to original source...
    10. NÁPRSTKOVÁ, N., CAIS, K., STANČEKOVÁ, D. (2014). Influence of AlSiMg0.3 alloy modification by Sb on the tool wear. In: Manufacturing Technology, Vol. 14, pp. 75 - 79. Go to original source...
    11. AKYILDIZ, H. K. (2013). Evaluating of cutting forces in thread machining. In: International Journal of Advanced Manufacturing Technology, Vol. 68, pp. 1601 - 1612. Springer. Go to original source...
    12. WANG, J. (2000). Evaluating of cutting forces in thread machining. In: Journal of Materials Processing Technology, Vol. 97, pp. 114 - 119. Elsevier BV. Go to original source...
    13. MRKVICA, I., NESLUŠAN, M., KONDERLA, R., JURKO, J., PANDA, A. (2013). Cutting forces by turning of incInconel 718 with inserts from different materials. In: Manufacturing Technology, Vol. 13, pp. 499 - 504. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content