Manufacturing Technology 2018, 18(2):201-207 | DOI: 10.21062/ujep/78.2018/a/1213-2489/MT/18/2/201

Qualitative Evaluation of Machined Surface of Aluminum Alloy AlCu4Mg1 Depend on Feed Rate

Frantisek Botko1, Michal Hatala1, Zuzana Mitalova1, Robert Cep2, Miroslav Rimar1, Andrej Bernat1, Jaroslav Vybostek1
1 Faculty of Manufacturing technologies with a seat in Presov, Technical University of Kosice, Bayerova 1 street, 080 01 Presov, Slovakia
2 Department of Machining and Assembly, VSB - Technical University of Ostrava, 708 33 Ostrava. Czech Republic

Aim of the article is evaluation of surface quality parameters Rz and Ra after turning of aluminum alloy. Turning is one of the wide spread manufacturing technologies used in industrial production. Experiment was focused on researching of influence of various cutting conditions on machined surface. Main aim of this article is comparison of surface roughness parameters Ra and Rz depending on feed rate and tool nose radius. Investigation and finding of optimal cutting conditions is necessary for economy of manufacturing organization. Despite extensive research carried out in the area of turning, there is always room for new research.

Keywords: Rate, Roughness, Surface Quality, Lathe

Published: April 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Botko F, Hatala M, Mitalova Z, Cep R, Rimar M, Bernat A, Vybostek J. Qualitative Evaluation of Machined Surface of Aluminum Alloy AlCu4Mg1 Depend on Feed Rate. Manufacturing Technology. 2018;18(2):201-207. doi: 10.21062/ujep/78.2018/a/1213-2489/MT/18/2/201.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Z. HUTYROVA, I. ORLOVSKY (2014). Assessment of micro-geometric and macro-geometric parameters after machining composite material with natural fibres, in: S. Fabian, T. Krenicky (Eds.), Operation and Diagnostics of Machines and Production Systems Operational States II book series: Applied Mechanics and Materials, 2014, pp. 267-283. Go to original source...
    2. J. DUPLAK, P. MICHALIK, M. KORMOS, et al. (2014). Impact of Cutting Speed on the Resultant Cutting Tools Durability in Turning Process of Steel 100CrMn6,in: S. Fabian, T. Krenicky (Eds.), Operation and diagnostics of machines and production systems operational states II., 2014, pp. 292-299. Go to original source...
    3. J. VALICEK, M. DRZIK,T. Hryniewicz (2012). Non-Contact Method for Surface Roughness Measurement After Machining, Measurement Science Review. 12 (2012) 184-188. Go to original source...
    4. J. ZAJAC, D. MITAL, P. MICHALIK (2014). Verification of process fluids in mass production,in: J. Kundrat, Z. Maros (Eds.), Precision Machining VII Book series: Key Engineering Materials, 2014, pp. 554-559. Go to original source...
    5. I. VOJTKO,V. SIMKULET, P. BARON, et al. (2014). Microstructural Characteristics Investigation of the Chip-Making Process after Machining,in: S. Fabian, T. Krenicky (Eds.), Operation and Diagnostics of Machines and Production Systems Operational States II book series: Applied Mechanics and Materials, 2014, pp. 344-350.
    6. J. ZIVCAK, M. PETRIK, R. HUDAK, et al. (2009). Embedded Tensile Strenght Test Machine FM1000-An Upgrade of Measurement and Control, in: Z. Gosiewski, Z. Kulesza (Eds.), Mechatronic systems and materials III., Book Series: Solid State Phenomena, 2009, pp. 657-662.
    7. J. KOVAL, Optimalization of Cutting Conditions of Turning (diploma thesis), 2015.
    8. S. F. KRAR, A. R. GILL, A. R. SMID (2011). Technology of Machine Tools, 7th ed., McGraw-Hill, New York, 2011.
    9. I. MUKHERJEE, P. K. RAY (2006). A review of Optimization Techniques in Metal Cutting Processes, Computer and Indrustrial engineering. 50 (2006) 15-34. Go to original source...
    10. CEP, R., JANASEK A., PETRU J., CEPOVA L., CZAN A., VALICEK J. (2013). Hard Machinable Machining of Cobalt-based Superalloy. In Manufacturing Technology, vol. 13, No. 2. pp. 226-231. ISSN 1213-2489 Go to original source...
    11. PETERKA J, POKORNÝ P. (2014). Influence of the lead angle from the vertical axis milling on effective radius of the cutter.in: Key Eng Mat 2014;581:44-9 Go to original source...
    12. KUDLÁČEK J, CHÁBERA P, ©IKULEC L. (2015). Luminescence method - instrument used for detection of surface cleanliness. Teh Vjesn 2015;22(4) Go to original source...
    13. J. CARACH, D. LEHOCKA, S. LEGUTKO, S. HLOCH, S. CHATTOPADHYAYA, A. R. DIXIT (2017). Surface roughness of graphite and aluminium alloy after hydro-abrasive machining, in: Lecture Notes in Mechanical Engineering, 5th International Scientific-Technical Conference on Advances in Manufacturing, MANUFACTURING 2017, 2018, pp. 805-813 Go to original source...
    14. BALOG M., SZILÁGYI E., DUPLÁKOVÁ D., MINĎA© M. (2016). Effect verification of external factor to readability of RFID transponder using least square In: Measurement. Vol. 94 (2016), p. 233-238. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content