Manufacturing Technology 2018, 18(3):493-498 | DOI: 10.21062/ujep/127.2018/a/1213-2489/MT/18/3/493

Nanofluids Application in the Drilling Process

Veikko Shalimba1, Bruno Sopko2
1 Faculty of Mechanical Engineering, J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7, 400 01 Usti nad Labem. Czech Republic
2 Institute of Material and Applied Physics, Czech Technical University in Prague, Horská 3a/22, 128 00 Praha 2, Czech Republic

A high performance of heat transfer fluid has a great influence on the size, weight and cost of heat transfer systems, therefore a high-performance heat transfer fluid is very important in many industries. Over the last decades nanofluids have been developed. According to many researchers and publications on nanofluids its evident that nanofluids are found to exhibit enhance thermal conductivity. The aim of this experiment was to investigate the change of workpiece temperature during drilling using Jatropha oil with nanoparticle and water with iron nanoparticle as lubricating and cooling fluids. These experiments were carried out with samples of nanofluid with different volume ratio. Samples JN1, JN5 and JN10 of iron nanoparticles in the base Jatropha oil with iron volume fraction 1%, 5% and 10% respectively. Samples WN1, WN5 and WN10 of iron nanoparticles in the base water with iron volume fraction 1%, 5% and 10% respectively. The work arises from the projects which were realized at University J. E. Purkyně, Faculty of Mechanical Engineering, in cooperation with Namibia University of Science and technology, department of Mechanical Engineering.

Keywords: Jatropha oil, nanofluids, nanoparticles, temperature, drilling

Published: June 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Shalimba V, Sopko B. Nanofluids Application in the Drilling Process. Manufacturing Technology. 2018;18(3):493-498. doi: 10.21062/ujep/127.2018/a/1213-2489/MT/18/3/493.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. CHOI, S., EASTMAN, J. (1995). Enhancing Thermal Conductivity of Fluids with Nanoparticles. Proceedings of the ASME Mechanical Engineering Congress and Exposition. USA, pp. 99-104. DOE W-31109-ENG-38.
    2. OZERINC, S. (2010). Heat transfer enhancement with nanofluids. Thesis, School of Natural and Applied Science: Middle East Technical University. 147p.
    3. GALLEGO, M., LUGO, L., LEGIDO, J. PINEIRO, M. (2011) Thermal Conductivity and Viscosity Measurements of Ethylene Glycol-Based Al2O3 Nanofluids. Nanoscale Research Letters. Springer Open, 11p. ISSN 1556-276X.
    4. MINKOWYCZ, W., SPARROW, E, W., ABRAHAM, J. (2013). Nanoparticle Heat transfer and Fluid Flow. New York, Tayloer & Francis Group, Vol. 4, 335p. ISBN 13: 978-14398-6195-0.
    5. DAS, K., CHOI, S., PRADDEP, T. (2007) Nanofluids Science and Technology. New Jersey, John Wiley & Son, 407p. ISBN 978-0-470-07473-2. Go to original source...
    6. TIMOFEEVA, E. (2011) Nanofluids for Heat Transfer - Potential and Engineering Strategies. Energy Systems Division, Argonne National Laboratory, Illinois, pp. 435-450. ISBN 978-953-307-584-6.
    7. RATHORE, M., KAPUNO, R.: Engineering Heat Transfer. (2011) Jones & Bartlett Learning, 1096p. ISBN 13:978-0-7637-7752-4.
    8. POPOV, A., KRASNIKOV, I. (2018) Reducing Labour Intensity in the Development of New Universal Cutting Fluids for Machning. Manufacturing Technology, Vol, 18, No. 1, pp. 99-105. ISSN 1213-2489. Go to original source...
    9. DAŇA, M., ZATEK, M., SCHORNÍK, V. (2017) Effect of Cutting Edge Geometry on Cutting Forces when Drilling Inconel 718. Manufacturing Technology, Vol, 17, No. 1, pp. 24-29. ISSN 1213-2489. Go to original source...
    10. NOVOTNÝ, J., LYSOŇKOVÁ, I., MICHNA, ©., NÁPRSTKOVÁ, N. (2017) Research of Application Possibilities of Selected Mechanical Alloyed Metal Powders. Manufacturing Technology, Vol, 17, No. 5, pp. 811-815. ISSN 1213-2489. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content