Manufacturing Technology 2018, 18(4):674-678 | DOI: 10.21062/ujep/159.2018/a/1213-2489/MT/18/4/674

Influence of Cutting Parameters on Cylindricity Deviation by Centerless Grinding

Dana Stancekova1, Pavol Martikan1, Jaroslava Svobodova2, Miroslav Janota1, Jiri Kratochvil3
1 University of Zilina, Faculty of Mechanical Engineering, Univerzitna 1, 010 26, Zilina, Slovak Republic
2 J. E. Purkyně University, Faculty of Production Technology and Management, Ústí nad Labem, Czech Republic
3 TU Ostrava, Faculty of Mechanical Engineering,17. listopadu 15/2172, 708 33 Ostrava, CZ

Grinding is one of the oldest ways of material machining operations. The requirement to produce fast and cost-effective parts in large quantities has classified the metal grinding in the engineering industry for major machining operation. The complexity of the abrasive process and the amount of abrasive tool parameters have considerable problems in the theoretical and experimental study of this process, which is machining with undefined cutting-edge tool. The submitted verifications are aimed at intensifying grinding without medium stress due to the cylindrical deviation. Also, these verifications are aimed to the adjustment of centreless grinding conditions for a given value of the geometric deviation of the shaft and the influence of the abrasive conditions on a given cylindricity deviation.

Keywords: Centreless grinding, Deviation of cylindrical, Speed

Published: September 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Stancekova D, Martikan P, Svobodova J, Janota M, Kratochvil J. Influence of Cutting Parameters on Cylindricity Deviation by Centerless Grinding. Manufacturing Technology. 2018;18(4):674-678. doi: 10.21062/ujep/159.2018/a/1213-2489/MT/18/4/674.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. STANČEKOVÁ, D., ŠTEKLÁČ, D., PETRU, J., ZLÁMAL, T., SADÍLEK, M., JANOTA, M., KORDÍK, M. (2016). Influence of Machining and Heat Treatment on Deformations of Thin-Walled Bearings. In Materials Science Forum, vol. 862/2016, p. 49-58, ISSN 0255-5476 Go to original source...
    2. TAVODOVÁ, M., KALINCOVÁ, D. (2016). Improving the Quality of Castings Using Thermovision. In. Manufacturing Technology, Volume 16, Issue 1, p 268-273, ISSN: 1213-2489 Go to original source...
    3. RADVANSKÁ, A.; HREHA, P.; KNAPČÍKOVÁ, L.; PETRŮ, J.; ZLÁMAL, T.; MONKA, P. (2015). Influence of focusing tube wear on vibrations and surfaces roughness. In Tehnicki Vjesnik - Technical Gazette, Vol. 22, No. 2, pp. 271-278. ISSN 1330-3651 Go to original source...
    4. SCHINDLEROVÁ, V., ŠAJDLEROVÁ, I., MOHYLA, P. (2016). Optimization of metallurgical processes using dynamic simulation. In METAL 2016: conference proceedings: (reviewed version) : 25th Anniversary International Conference on Metallurgy and Materials : May 25th-27th 2016, Hotel Voronez I, Brno, Czech Republic, EU. Ostrava: Tanger, 2016, s. 2013-2018.
    5. LIPTAK, O. a kol. (1979). Technológia výroby - obrábanie, Bratislava: ALFA,1979, 444 p.
    6. MONKOVA, K., MONKA, P., MATEJKA, J., NOVAK, M., CESANEK, J., DUCHEK, V., URBAN, M. (2017). Surface machining after deposition of wear resistant hard coats by high velocity oxygen fuel technology. In. Manufacturing Technology, Vol. 17, Issue 6, p. 919-925 Go to original source...
    7. CZAN, A., SAJGALIK, M., ZAUSKOVA, L., CEP, R., RYSAVA, Z., SORDI, V.L. (2017). Investigation of stress status in the micro-space of surface and subsurface layers. In. Communications - Scientific Letters of the University of Zilina, Volume 19, Issue 2, p 112-116, ISSN: 1335-4205 Go to original source...
    8. http://www.junker-group.com/grinding/loesungen/schleifmaschinen/jupiter.php[25-11-2009]
    9. MEDVECKY, Š. a kol. (1999). Základy konštruovania, Žilina: EDIS, 1999, 599s.
    10. NOVOTNÝ, J., CAIS, J., NÁPRSTKOVÁ, N. (2014). Analysis of aluminium alloys AlSi7Mg0.3 and AlMg3 by means of X-Ray Diffraction, In Manufacturing Technology, Vol. 14, No. 3, FVTM UJEP, Ústí nad Labem, pp. 392-397. ISSN 1213-2489 Go to original source...
    11. VALÁŠEK, P., MÜLLER, M. (2015). Abrasive wear in three-phase waste based polymeric particle composites. In. Tehnicki Vjesnik-Technical Gazette, vol. 12, 2/2015, pp. 257-262. Go to original source...
    12. http://web.tuke.sk/smetrologia/navody/uloha9.pdf[22-11-2009]
    13. http://sk.autolexicon.net/articles/kompresor-eaton[22-11-2009]
    14. http://www.koyo-machine.co.jp/English/pdf/Centerless_Grinding_machines.pdf[22-11-2009]

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content