Manufacturing Technology 2019, 19(1):168-171 | DOI: 10.21062/ujep/263.2019/a/1213-2489/MT/19/1/168

Characteristic Signal of FT3 Measuring Probe

Jiri Vit1, Martin Novak ORCID...2
1 Hommel CS, Karoliny Svetle 2546, 415 01 Teplice. Czech Republic
2 Faculty of Mechanical Engineering, J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7, 400 01 Usti nad Labem. Czech Republic

The article deals with the determining of the characteristic signal of the inductive FT3 measuring probe, that is used on the roundness machines of Jenoptik IM producer. The research was the basis for generalized recommendations for the calibration of the probe, which was published in the article "A roundness machine measuring probe calibration". The signals of eight FT3 probes have been acquired and evaluated for repeatability and mutual equality. Five signals of each individual probe were taken immediately for repeatability evaluation. The deviations of the individual signals from the mean signal and the deviations of the signal first derivative curves from the mean first derivative curve have been evaluated for the repeatability evaluation. The deviations of the signal of the individual probes from the perfect signal have been evaluated for the equality evaluation.

Keywords: Matlab, probe signal, roundness machine

Published: February 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Vit J, Novak M. Characteristic Signal of FT3 Measuring Probe. Manufacturing Technology. 2019;19(1):168-171. doi: 10.21062/ujep/263.2019/a/1213-2489/MT/19/1/168.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. VÍT, J., NOVÁK, M. (2018) A roundness machine probe calibration. In Manufacturing Technology, Vol. 18, No. 6, pp. 1053-1059. ISSN 1213-2489. Go to original source...
    2. VÍT, J. (2017) Procedure library for roundness machine probe signal exploration. Usti nad Labem, 2017. Study for dissertation theses. Faculty of Mechanical Engineering, J. E. Purkyne University. Supervisor Martin Novak
    3. -. Surface metrology open profile Gaussian filter. Library of procedures. [online]. 06. 09 2015. Matlab Central File Exchange. [Citation: 18. 10 2018.] Available on: http://www.mathworks.com/matlabcentral/fileexchange/52892-surface-metrology-open-profile-gaussian-filter.
    4. -. Surface metrology open profile spline filter. Library of procedures. [online]. 19. 08 2015 Matlab Central File Exchange. [Citation: 18. 10 2018.] Available on: http://www.mathworks.com/matlabcentral/fileexchange/52562-surface-metrology-open-profile-spline-filter.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content