Manufacturing Technology 2019, 19(2):284-291 | DOI: 10.21062/ujep/284.2019/a/1213-2489/MT/19/2/284

The Impact of Changes in InFeed Rate on Surface Integrity after Chrome Plate Grinding by Silicon Carbide

Martin Marek, Martin Novák, Karel ©ramhauser
Faculty of Mechanical Engineering, J. E. Purkyně University in Usti nad Labem, Pasteurova 3334/7, 400 01 Ústí nad Labem

Grinding is a significant and very commonly used technology, allowing for important gains in surface integrity. The surface integrity quality after grinding is one of the most important parameters, which is prescribed on the production drawing. Chrome plating as protection against corrosion, erosion, abrasion and as a material for the overhaul of worn-out parts is used. This paper discusses the change of cutting conditions when samples were ground. The surface of all samples was preserved with galvanically applied chrome. The values show which grade of surface roughness is attained when selecting different cutting conditions. The results of surface integrity after grinding were evaluated depending on the comparison of the parameters of roughness. The input parameters of cutting conditions were chosen based on the experience, which was implemented.

Keywords: grinding, hard chrome plate, surface integrity, cutting conditions
Grants and funding:

Solar Turbines EAME Ltd.
Project UJEP-SGS-2017-48- 002-2.

Published: April 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Marek M, Novák M, ©ramhauser K. The Impact of Changes in InFeed Rate on Surface Integrity after Chrome Plate Grinding by Silicon Carbide. Manufacturing Technology. 2019;19(2):284-291. doi: 10.21062/ujep/284.2019/a/1213-2489/MT/19/2/284.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. MASLOV, J., N. (1979). Teorie brouąení kovů. Praha: SNTL - Nakladatelství technické literatury, n. p., 1979. 244-248 s.
    2. MÁDL, J., KAFKA, J., VRABEC, M., DVOŘÁK, R. (2000). Technologie obrábění, 3. díl. Praha: ČVUT, 2000. 81 s.
    3. G. E. DIETER (1989). Mechanical Metallurgy, McGraw Hill Higher Education, 1989.
    4. MAREK, M., NOVÁK, M., HOLESOVSKY, F., DURAKBASA, M., N. (2017). The Effect of Changes to Nickel Coating Machine on Surface Integrity and Microstructure after Grinding, In: Manufacturing Technology, Vol. 17, No. 6 (2017) pp.906-912, ISSN: 1213-2489. Go to original source...
    5. NOVAK, M., NAPRSTKOVA, N. (2015). Grinding of the Alloy INCONEL 718 and Final Roughness of the Surface and Material Share. In: Manufacturing Technology, Vol. 15, No. 6 (2015) pp.1015-1023, ISSN: 1213-2489. Go to original source...
    6. MAREK, M., NOVÁK, M. (2017). The Effect of Changes in Feed Rate on Surface Integrity during Nickel Coating Grinding, Solid State Phenomena, Vol. 261, pp. 207-214, 2017 Go to original source...
    7. MAREK, M., NOVÁK, M, SRAMHAUSER, K., SVOBODOVA, J. (2018). Analysis of the base material and hard chrome plated layer in an unloaded state, In: Manufacturing Technology, Vol. 18, No. 4 (2018) pp.616-620, ISSN: 1213-2489. Go to original source...
    8. MALLORY, G. O. a J. B. HAJDU. (1990). Electroless Plating - Fundamentals and Applications. Orlando: William Andrew Publishing/Noyes, 1990, 575 s. ISBN 978-0815512776.
    9. KRAUS, V. (2000). Povrchy a jejich úpravy. Plzeň: Západočeská univerzita v Plzni, 2000. ISBN 80-7082-668-1.
    10. JINFENG ZHANG, CHAO FENG, YUNHUI MA, WEI TANG, SHUAI WANG, XIN ZHONG. (2017). Nondestructive analysis of surface integrity in turning and grinding operations In: Manufacturing Technology, Vol. 17, No. 3, pp. 412-418, ISSN:1213-2489. Go to original source...
    11. OBR, L. Funkční chromování - HEEF 25. Povrchové úpravy. 2008, č. 2. Dostupné z: http://www.povrchoveupravy.cz/2008-02-clanek04.html
    12. GOSTIMIROVIĆ, MARIN & RODIC, DRAGAN & KOVAC, PAVEL & JE©IĆ, DI©AN & KULUND®IĆ, NENAD. (2015). Investigation of the cutting forces in creep-feed surface grinding proces. Journal of Production Engineering. 18. 21-24.
    13. C. YAO, Q. JIN, X. HUANG, D. WU, J. REN AND D. ZHANG, "Research on surface integrity of grinding Inconel 718," Int J Adv Manuf REFERENCES | 68 Technol, vol. 65, pp. 1019-1030, 2013.
    14. Tvrdé chromování. BOMEX CZ. Bomex [online]. 1999 [cit. 2012-04-18]. Dostupné z: http://www.bomex.cz/cz/3-technologie/8-tvrde-chromovani.html

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content