Manufacturing Technology 2020, 20(3):347-354 | DOI: 10.21062/mft.2020.035

The Research of the Different Properties and Production Parameters having Influence on Deep-Drawing Sheets made of AlMg3 Alloy

©tefan Michna, Iryna Hren, Jaromír Cais, Lenka Michnová
University of J. E. Purkyně, Faculty of Mechanical Engineering, Ústí nad Labe, Pasteurova 3334/7, Czech Republic

This work was focused on the research of the different variability production deep-drawing sheets made of AlMg3 alloy which could influence on their deep-drawing properties e.g. non alloying elements Fe, Mn, heat treatment parameters and structure with aim to judge ascertained and analyzed properties of the sheets. The mechanical properties, mainly the highest elongation, and the other parameters (grain size, metallurgical purity), were measured due to they had had the main influence on the deep-drawing properties of the sheets made of AlMg3 alloy. For this research work had been obtained 5 deep-drawing sheets made of AlMg3 alloy with different production than chemical composition and heat treatment with the aim to realized ?complex analyze?, and to find up the best variant for production technology with the high deep-drawing properties.

Keywords: AlMg3 alloy, mechanical properties, elongation of material, deep-drawing, chemical composition, aluminum sheets, metallurgical purity, EDS analyses, grain size
Grants and funding:

ESIF Project Development of new nano and micro coatings on the surface of selected metallic materials - NANOTECH ITI II., Reg. No CZ.02.1.01/0.0/0.0/18_069/0010045.

Prepublished online: September 3, 2020; Published: September 7, 2020  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Michna ©, Hren I, Cais J, Michnová L. The Research of the Different Properties and Production Parameters having Influence on Deep-Drawing Sheets made of AlMg3 Alloy. Manufacturing Technology. 2020;20(3):347-354. doi: 10.21062/mft.2020.035.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BANABIC D. (2010). Sheet Metal Forming Process. Springer. ISBN 978-3-540-88113-1. Go to original source...
    2. https://www.opi.zcu.cz/mechvlast.html
    3. HLUCHÝ. M., KOLOUCH J. (2007). Strojírenská technologie 1 - Nauka omateriálu. Praha: Scientia. ISBN 978-80-86960-26-5.
    4. HREN, I., MICHNA, ©., MICHNOVÁ, L. (2018). Dependence of mechanical properties on porosity of AlSi7Mg0.3 alloy during gravity casting. Engineering for Rural Development, Vol. 18, pp. 1001-1006. Go to original source...
    5. HREN, I., MICHNA, ©., CAIS, J., MICHNOVÁ, L., SVOBODOVÁ, J., HODINÁŘ, L. (2018). Beryllium influence on the modification in Al-Si alloy. Metallofizika a Noveishie Technologii, Vol. 12, pp. 1637-1647. Go to original source...
    6. MICHNA, ©. a kol. (2005). Encyklopedie hliníku. 1. Vydání, Preąov, SR: Adin s. r. o., 700 p.
    7. BOLIBRUCHOVÁ., TILLOVÁ, E. (2005). Zlievarenské zliatiny Al-Si. ®ilina: EDIS - vydavateµstvo ®U.
    8. MONDOLFO L. F. (1979). Aluminium Alloys, Structure and Properties. London: Butterworths, 986 p.
    9. MICHNA ©., KU¦MIERCZAK S. (2012). Praktická metalografie. Ústí nad Labem: UJEP in Ústí nad Labem, print OPTYS spol s.r.o., r., 245 p.
    10. CAIS J., MICHNA ©. (2015). Research of Influence of Heat Treatment on Microstructure and Mechanical Properties of AlSi9CuNiMn Alloy. Manufacturing Technology, Vol. 15, No. 5, pp. 43-46. ISSN 1213-2489.
    11. MICHNA ©., CAIS J., MICHNOVÁ L. (2015). Research of the Cause Cracking Hot-Rolled Block Made of AlMg5 Alloys. Manufacturing Technology, Vol. 15, No. 4, pp. 614-620. Go to original source...
    12. MARCHWICA, P. (2012). Microstructual and Thermal Analysis of Aluminum-Silicon and Magnesium-Aluminum Alloys Subjected to High Cooling Rates. Electronic Theses and Dissertations. 557
    13. UHRÍČIK, M., PALČEK, P., CHALUPOVÁ, M., OR©ULOVÁ, T. (2017). The Structure of the Aluminium Alloy and Its Influence on the Fatigue Properties. Manufacturing Technology. Vol. 17, No. 5, pp. 863-869. ISSN 1213-2489. Go to original source...
    14. NACHTNEBL, P., KOLAŘÍK, L., FOREJTOVÁ, L., REISGEN, U., BEHR, W. (2018) Ultrasonic Testing of Diffusion Bonded Joints of AlMg3. Manufacturing Technology. Vol. 18, No.2, pp. 289-294. ISSN 1213-2489. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content