Manufacturing Technology 2021, 21(6):736-748 | DOI: 10.21062/mft.2021.089
Lattice structure design parameters optimization for the structural integrity of passive vibration isolator
- 1 Fakulti Kejuruteraan Mekanikal, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
- 2 Centre for Advanced Research on Energy, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
Passive vibration isolator with lower natural frequency has always been a challenge due to structural integrity issues. This study presents the use of RSM statistical tool to analyze and optimize the mechan-ical responses of BCC lattice structure for structural integrity in a passive vibration isolator application. The optimization was done to obtain low stiffness for low natural frequency but high yield stress for optimum load-bearing capability with unit cell size and strut diameter design parameters tweak. From the results, the significance and contribution of each design parameter on each mechanical response through compression test can be understood. Results indicated changes in strut diameter produced lin-ear growth while changes in the unit cell size produced inverse exponential responses. From optimiza-tion, a combination of 3.9 mm strut diameter with 10 mm unit cell size produced the optimum result. Therefore, it was demonstrated that RSM can provide statistical importance and contribution between input factors and their influence on each mechanical response with minimal test and cost.
Keywords: Lattice structure; Design parameter; Optimization; Structural integrity; Vibration isolator
Grants and funding:
The authors acknowledge the scholarship from Zamalah Scheme, Universiti Teknikal Malaysia Melaka.
Received: August 24, 2021; Revised: November 25, 2021; Accepted: December 1, 2021; Prepublished online: December 21, 2021; Published: January 8, 2022 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- Abdulhadi, H.S. and Mian, A. (2019), "Effect of strut length and orientation on elastic mechanical response of modified body-centered cubic lattice structures", Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Vol. 233 No. 11, pp. 2219-2233.
Go to original source...
- Ashby, M.F., Evans, T., Fleck, N.A., Hutchinson, J.W., Wadley, H.N.G. and Gibson, L.J. (2000), Metal Foams: A Design Guide, Elsevier.
Go to original source...
- Bai, L., Zhang, J., Xiong, Y., Chen, X., Sun, Y., Gong, C., Pu, H., et al. (2020), "Influence of unit cell pose on the mechanical properties of Ti6Al4V lattice structures manufactured by selective laser melting", Additive Manufacturing, Vol. 34, p. 101222.
Go to original source...
- Baravelli, E., Carrara, M. and Ruzzene, M. (2013), "High stiffness, high damping chiral metamaterial assemblies for low-frequency applications", Health Monitoring of Structural and Biological Systems 2013, Vol. 8695, p. 86952K.
Go to original source...
- Buonamici, F., Carfagni, M., Furferi, R., Governi, L., Saccardi, M. and Volpe, Y. (2018), "Optimizing fabrication outcome in low-cost FDM machines. Part 2 - Tests", Manufacturing Technology, Vol. 18 No. 4, pp. 552-558.
Go to original source...
- Christensen, R.M. (2008), "Observations on the definition of yield stress", Acta Mechanica, Vol. 196 No. 3, pp. 239-244.
Go to original source...
- Deng, Y., Mao, Z., Yang, N., Niu, X. and Lu, X. (2020), "Collaborative optimization of density and surface roughness of 316L stainless steel in selective laser melting", Materials, Vol. 13 No. 7, p. 1601.
Go to original source...
- El-Sayed, M.A., Essa, K., Ghazy, M. and Hassanin, H. (2020), "Design optimization of additively manufactured titanium lattice structures for biomedical implants", The International Journal of Advanced Manufacturing Technology, Vol. 110 No. 9, pp. 2257-2268.
Go to original source...
- Elmadih, W.A., Syam, W.P., Maskery, I. and Leach, R. (2017), "Additively manufactured lattice structures for precision engineering applications", In Proceedings of the 32nd Annual Meeting of American Society for Precision Engineering, pp. 164-169.
- Gautam, R. and Idapalapati, S. (2019), "Compressive properties of additively manufactured functionally graded Kagome lattice structure", Metals, Vol. 9 No. 5, p. 517.
Go to original source...
- Hanzl, P., Zetková, I. and Cajthamlová, İ. (2019). "Influence of strut diameter and building direction on strength of lattice structure", Manufacturing Technology, Vol. 19 No. 6, pp. 947-951.
Go to original source...
- Hasan, R. (2013), Progressive Collapse of Titanium Alloy Micro-Lattice Structures Manufactured Using Selective Laser Melting, University of Liverpool.
- Helou, M. and Kara, S. (2018), "Design, analysis and manufacturing of lattice structures: an overview", International Journal of Computer Integrated Manufacturing, Vol. 31 No. 3, pp. 243-261.
Go to original source...
- Hossain, U., Ghouse, S., Nai, K. and Jeffers, J.R. (2021), "Controlling and testing anisotropy in additively manufactured stochastic structures", Additive Manufacturing, Vol. 39, p. 101849.
Go to original source...
- Hull, D. and Bacon, D.J. (2011), Introduction to Dislocations, Elsevier.
Go to original source...
- Iyibilgin, O., Yigit, C. and Leu, M.C. (2013), "Experimental investigation of different cellular lattice structures manufactured by fused deposition modeling", Proceedings of the Solid Freeform Fabrication Symposium, Austin, TX, USA, pp. 895-907.
- Karmoker, J.R., Hasan, I., Ahmed, N., Saifuddin, M. and Reza, M.S. (2019), "Development and Optimization of Acyclovir Loaded Mucoadhesive Microspheres by Box-Behnken Design", Dhaka University Journal of Pharmaceutical Sciences, Vol. 18 No. 1, pp. 1-12.
Go to original source...
- Khuri, A.I. (2001), "An overview of the use of generalized linear models in response surface methodology", Nonlinear Analysis: Theory, Methods & Applications, Vol. 47 No. 3, pp. 2023-2034.
Go to original source...
- Khuri, A.I. and Cornell, J.A. (2018), Response Surfaces: Designs and Analyses, Routledge.
Go to original source...
- Kiernan, D. (2014), Natural Resources Biometrics, Open SUNY Textbooks.
- Lagoudas, D.C., Mayes, J.J. and Khan, M.M. (2001), "Simplified shape memory alloy (SMA) material model for vibration isolation", Smart Structures and Materials 2001: Modeling, Signal Processing, and Control in Smart Structures, Vol. 4326, pp. 452-461.
Go to original source...
- Mahshid, R., Hansen, H.N. and Højbjerre, K.L. (2016), "Strength analysis and modeling of cellular lattice structures manufactured using selective laser melting for tooling applications", Materials & Design, Vol. 104, pp. 276-283.
Go to original source...
- Maskery, I., Hussey, A., Panesar, A., Aremu, A., Tuck, C., Ashcroft, I. and Hague, R. (2017), "An investigation into reinforced and functionally graded lattice structures", Journal of Cellular Plastics, Vol. 53 No. 2, pp. 151-165.
Go to original source...
- Matsumoto, H., Watanabe, S. and Hanada, S. (2005), "Beta TiNbSn alloys with low Young's modulus and high strength", Materials Transactions, Vol. 46 No. 5, pp. 1070-1078.
Go to original source...
- Monkova, K., Vasina, M., Zaludek, M., Monka, P.P. and Tkac, J. (2021), "Mechanical Vibration Damping and Compression Properties of a Lattice Structure", Materials, Vol. 14 No. 6, p. 1502.
Go to original source...
- Ngo, T.D., Kashani, A., Imbalzano, G., Nguyen, K.T.Q. and Hui, D. (2018), "Additive manufacturing (3D printing): A review of materials, methods, applications and challenges", Composites Part B: Engineering, Vol. 143, pp. 172-196.
Go to original source...
- Pat. (2017), "The importance of center points in central composite designs", available at: https://www.statease.com/blog/importance-center-points-central-composite-designs/ (accessed 15 August 2021).
- Pernica, J., Sustr, M., Dostal, P., Brabec, M. and Dobrocky, D. (2021), "Tensile Testing of 3D Printed Materials Made by Different Temperature", Manufacturing Technology, Vol. 21 No. 3, pp. 398-404.
Go to original source...
- Rashed, M.G., Ashraf, M., Mines, R.A.W. and Hazell, P.J. (2016), "Metallic microlattice materials: A current state of the art on manufacturing, mechanical properties and applications", Materials & Design, Vol. 95, pp. 518-533.
Go to original source...
- Rosli, N.A., Hasan, R., Alkahari, M.R. and Tokoroyama, T. (2017), "Effect of process parameters on the geometrical quality of ABS polymer lattice structure", Proceedings of SAKURA Symposium on Mechanical Science and Engineering 2017, pp. 3-5.
- Syam, W.P., Jianwei, W., Zhao, B., Maskery, I., Elmadih, W. and Leach, R. (2018), "Design and analysis of strut-based lattice structures for vibration isolation", Precision Engineering, Vol. 52, pp. 494-506.
Go to original source...
- Terner, M., Ricordel, T., Cho, J.-H. and Lee, J.-S. (2019), "The response surface methodology for optimizing the process parameters of selective laser melting", Journal of Welding and Joining, Vol. 37 No. 1, pp. 27-39.
Go to original source...
- Vilanova, M., Escribano-García, R., Guraya, T. and San Sebastian, M. (2020), "Optimizing Laser Powder Bed Fusion Parameters for IN-738LC by Response Surface Method", Materials, Vol. 13 No. 21, p. 4879.
Go to original source...
- Wang, G., Huang, L., Liu, Z., Qin, Z., He, W., Liu, F., Chen, C., et al. (2020), "Process optimization and mechanical properties of oxide dispersion strengthened nickel-based superalloy by selective laser melting", Materials & Design, Vol. 188, p. 108418.
Go to original source...
- Yan, L. and Gong, X. (2017), "Experimental study of vibration isolation characteristics of a geometric anti-spring isolator", Applied Sciences, Vol. 7 No. 7, p. 711.
Go to original source...
- Zeng, C., Liu, L., Bian, W., Leng, J. and Liu, Y. (2021), "Compression behavior and energy absorption of 3D printed continuous fiber reinforced composite honeycomb structures with shape memory effects", Additive Manufacturing, Vol. 38, p. 101842.
Go to original source...
- Zhang, F., Shao, S., Tian, Z., Xu, M. and Xie, S. (2019), "Active-passive hybrid vibration isolation with magnetic negative stiffness isolator based on Maxwell normal stress", Mechanical Systems and Signal Processing, Vol. 123, pp. 244-263.
Go to original source...
- Zhang, L., Feih, S., Daynes, S., Chang, S., Wang, M.Y., Wei, J. and Lu, W.F. (2018), "Energy absorption characteristics of metallic triply periodic minimal surface sheet structures under compressive loading", Additive Manufacturing, Vol. 23, pp. 505-515.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.