Manufacturing Technology 2023, 23(4):564-578 | DOI: 10.21062/mft.2023.037
Advances in Surface Laser Cladding Remanufacturing of Shaft Parts
- College of mechanical and vehicle engineering, Changchun University, Changchun, Jilin Province, China
This paper provides an overview of the commonly used processes and equipment for laser cladding, including pre-set powder feeding, simultaneous powder feeding, wire feeding cladding, and coaxial cladding nozzles. By comparing the above processes and related nozzles, the coating characteristics are summarized for the selection of appropriate methods and equipment in different working environments. Meanwhile, the morphology and properties of the clad layers of shaft parts processed with different process parameters (e.g. laser power, scanning speed, lap rate, powder feed rate) and the influence of the combined parameters are overviewed. The changes and mechanisms of metals, ceramics, and metal-ceramic composites in terms of hardness, wear resistance, metallurgical bonding, and microstructure are analyzed. In addition, the application of numerical simulation techniques to simulate the temperature and stress fields and to plan the melting trajectory when laser cladding processing is performed on the surface of shaft parts are reviewed. Finally, the problems in the current research on laser cladding of shaft parts are summarized and the development directions are discussed.
Keywords: Shaft part; Laser cladding; Process parameters; Cladding materials
Grants and funding:
This work was financially supported by the Science and Technology Project of Jilin Provincial Science and Technology Department of China (20200201220JC); Jilin Provincial Education Department Science and Technology Plan Project (JJKH20220589CY), and authors wish to express their gratitude.
Received: October 5, 2022; Revised: May 19, 2023; Accepted: May 29, 2023; Prepublished online: September 1, 2023; Published: September 5, 2023 Show citation
References
- CHANGSAI, L., YUJIANG, W., ZHONGQI, S., SHICHENG, W., LIANG, Y., YUEBIN, L. (2018). State-of-arts and perspectives of crankshaft repair and remanufacture. In: Materials Review, Vol. 32, No. 1, pp. 141-148.
- MITTAL, K.L., BAHNERS, T, (2007). Laser Surface Modification and Adhesion, pp. 203-262. China Machine Press, John Wiley & SonsIn. ISBN
- ABIOYE, T.E., FARAYIBI, P.K., CLARE,A.T. (2017). A comparative study of Inconel 625 laser cladding by wire and powder feed stock. In: Materials and Manufacturing Processes, Vol. 32, No. 14, pp. 1653-1659.
Go to original source...
- FARAYIBI, P.K., ABIOYE, T.E., CLARE, A.T. (2016). A parametric study on laser cladding of Ti-6Al-4Vwire and WC/W2C powder. In: International Journal of Advanced Manufacturing Technology, Vol. 87, No. 5, pp. 3349-3358.
Go to original source...
- LIU, H., HE, X., YU, G., WANG, Z., LI, S., ZHENG, C. (2015). Numerical simulation of powder transport behavior in laser cladding with coaxial powder feeding. In: Science China Physics, Mechanics & Astronomy, Vol. 58, No. 10, pp. 1-10.
Go to original source...
- DOUBENSKAIA, M., KULISH, A., SOVA, A., PETROVSKIY, P. (2021). Experimental and numerical study of gas-powder flux in coaxial laser cladding nozzles of Precitec. In: Surface and Coatings Technology, Vol. 406, No. 10, pp. 126672.
Go to original source...
- DA SILVA, M. D., PARTES, K., SEEFELD, T., VOLLERTSEN, F. (2012). Comparison of coaxial and off-axis nozzle configurations in one step process laser cladding on aluminum substrate(Article). In: Jour-nal of Materials Processing Technology, Vol. 212, No. 11, pp. 2514-2519.
Go to original source...
- NAGULIN K.Y., ISKHAKOV F.R., SHPILEV A I. (2018). Optical diagnostics and optimization of the gaspowder flow in the nozzles for laser cladding. In: Optics & Laser Technology, Vol. 108, No. 1, pp. 310-320.
Go to original source...
- SILVELLO, A., PERRONE, A. (2021). Laser Cladding of Metals, pp. 197-247. Springer, Pasquale. ISBN
- ZHU, L., XUE, P., LAN, Q., MENG, G., REN, Y., YANG, Z. (2021). Recent research and development status of laser cladding: A review. In: Optics & Laser Technology, Vol. 138, No. 1, pp. 106915.
Go to original source...
- KOEHLER, H., PARTES, K., SEEFELD, T. & VOLLERTSEN, F. (2010). Laser reconditioning of crankshafts: From lab to application. In: Physics Procedia, Vol. 5, No. 1, pp. 387-397.
Go to original source...
- FU, F., ZHANG, Y., CHANG, G., & DAI, J. (2016). Analysis on the physical mechanism of laser cladding crack and its influence factors. In: Optik, Vol. 127, No. 1, pp. 200-202.
Go to original source...
- HOFMAN, J.T., DE LANGE, D.F., PATHIRAJ, B. (2011). FEM modeling and experimental verification for dilution control in laser cladding. In: Journal of Materials Processing Technology, Vol. 211, No. 2, pp. 187-196.
Go to original source...
- ZHANG, L., CHEN, X.,ZHANG, K., JIANG, Z., MAO, P., FU, L. (2019). Microstructure and Wear/Corrosion Resistance of Laser Cladding Ni-Based Coating on Hydraulic Piston Rod for Coastal Sluice. In: Materials Protection, Vol. 52, No. 11, pp. 117-22.
- ZHAO, Y., GUAN, C., CHEN, L. (2020). Effect of process parameters on the cladding track geometry fabricated by laser cladding. In: Optik, Vol. 223, No. 1, pp. 165-447.
Go to original source...
- LIAN, G., ZHAO, C., ZHANG, Y. (2021). Forming control in single-track laser cladding on crankshaft based on multiobjective optimization. In: JOM, Vol. 73, No. 12, pp. 4319-4327.
Go to original source...
- HAN, Y., LU, J., LI, J., SUN, J., LIU, Y. (2015). Lathe spindle remanufacturing based on laser cladding technology. In: China Surface Engineering, Vol. 28, No. 6, pp. 147-153.
- JIAO, X., WANG, J., WANG, C., GONG, Z., PANG, X., & XIONG, S. (2018). Effect of laser scanning speed on microstructure and wear properties of T15M cladding coating fabricated by laser cladding tech-nology. In: Optics and Lasers in Engineering, Vol. 110, No. 1, pp. 163-171.
Go to original source...
- AN, X.L., WANG, Y.L., JIANG, F.L., ZHANG J., ZHANG, J.Y. (2021). Effect of overlap rate on the temperature field and residual stress distribution in 42CrMo laser clad layersy. In: Chinese Journal of La-sers, Vol. 48, No. 10, pp. 95-106.
- FANG, Z.X., QI, W.J., LI, Z.Q. (2021). Effect of laser Effect of laser cladding lap ratio of 304 stainless steel on microstructure, wear resistance and corrosion resistance of CoCrW coating. In: Materials Reports, Vol. 35, No. 12, pp. 12123-12129.
- JUN. W., DONGDONG, Z., RICHU, Y. (2016). Parameters optimization and friction and wear properties for laser cladding Ni60AA coating on 45 steel shaft surface. In: Laser & Optoelectronics Progress, Vol. 58, No. 11, pp. 1114008.
- LINSEN, S., BO, W., YAYIN, H. (2019). Optimization of process parameters of laser cladding 304L alloy powder based on orthogonal experiment. In:Mechanical Engineering Science, Vol. 1, No. 2, pp. 10-21.
Go to original source...
- SHU, D., DAI, S., SUN, J. (2020). Parameters Research on optimization of laser cladding process parameters based on orthogonal experimental method. In: Key Engineering Materials, Vol. 1, No. 2, pp. 10-21.
Go to original source...
- SHI, Y., LI, Y., LIU, J. (2018). Investigation on the parameter optimization and performance of laser cladding a gradient composite coating by a mixed powder of Co50 and Ni/WC on 20CrMnTi low carbon alloy steel. In: Optics & Laser Technology, Vol. 99, No. 2, pp. 256-270.
Go to original source...
- CHEN, Y., WANG, X., ZHAO, Y. (2020). Interactive optimization of process parameters and coating analysis of laser cladding JG-3 powderl. In: The International Journal of Advanced Manufacturing Tech-nology, Vol. 107, No. 5, pp. 2623-2633.
Go to original source...
- SHI, B., LI, T., GUO, Z. (2022). Selecting process parameters of crack-free Ni60A alloy coating prepared by coaxial laser cladding. In: Optics & Laser Technology, Vol. 149, No. 5, pp. 107805.
Go to original source...
- HUI,Z., ZHIREN, H., JIANG, C. (2010). Experimental investigation on shaft straightening based on laser cladding. In: Journal of Northeastern University(Natural Science), Vol. 31, No. 12, pp. 1729-1732.
- JIANQUN, H., CHENGWU, W., JINGWEN, W., WENTAO, W., ZHIWEI, L., JINGWEI, H., ZIQIANG, Y., WEI, C. (2021). Laser cladding remanufacturing technology of 12CrNi3A steel camshaft. In: Heat Treatment of Metals, Vol. 46, No. 2, pp. 0254-6051.
- XU, M., LI, J., JIANG, J. (2015). Influence of powders and process parameters on bonding shear strength and micro hardness in laser cladding remanufacturing. In: Procedia Cirp, Vol. 29, No. 2, pp. 804-809.
Go to original source...
- ADITYA, Y.N., SRICHANDRA, T.D., TAK, M. (2021). To study the laser cladding of ultra high strength AerMet-100 alloy powder on AISI-4340 steel for repair and refurbishment. In: Materials Today: Proceed-ings, Vol. 41, No. 1, pp. 1146-1155.
Go to original source...
- HAN, T., XIAO, M., ZHANG, Y. (2019). Effect of Cr content on microstructure and properties of Ni-Ti-xCr coatings by laser cladding. In: Optik, Vol. 179, No. 1, pp. 1042-1048.
Go to original source...
- WANG, K., CHANG, B., CHEN, J. (2017). Effect of molybdenum on the microstructures and properties of stainless steel coatings by laser cladding. In: Applied Sciences, Vol. 7, No. 10, pp. 1065.
Go to original source...
- YA, S., CHANGJUN, W., YA, L.,HAOPING, P., (2019). Xuping, Su. Impact of alloying elements on the phase composition and mechanical properties of the CoCrFeNi-based high entropy alloys: A Review, In: Materials Reports, Vol. 33, No. 7, pp. 1169-1173.
- SHIXIN, C., WEINING, L.,WEIBIN, REN., BING, X. (2021). Microstructures and performance of la-ser cladding and quenching remanufactured cladding layer on QT700 ductile cast iron gear surface. In: La-ser & Optoelectronics Progress, Vol. 58, No. 5, pp. 186-193.
Go to original source...
- CHEN, L., YU, T., XU, P. (2021). In-situ NbC reinforced Fe-based coating by laser cladding: Simulation and experiment. In: Surface and Coatings Technology, Vol. 412, No. 3, pp. 127027..
Go to original source...
- WU, Q., LI, W., ZHONG, N,. (2013). Microstructure and wear behavior of laser cladding VC-Cr7C3 ceramic coating on steel substrate. In: Materials & design, In: Vol. 49, No. 7, pp. 10-18.
Go to original source...
- JIANING, L., CHUANZHONG, C., LEI, Z. (2011). Microstructure characteristics of Ti3Al/TiC ceramic layer deposited by laser cladding. In: International Journal of Refractory Metals and Hard Materials, Vol. 29, No. 1, pp. 49-53.
Go to original source...
- TONG, W., ZHAO, Z., ZHANG, X. (2017). Microstructure and properties of TiC/Co-Based alloy by la-ser cladding on the surface of nodular graphite cast Iron. In: Acta Metall Sin, Vol. 53, No. 4, pp. 472-478.
- CHEN, L., ZHAO, Y., CHEN, X. (2021). Repair of spline shaft by lasercladding coarse TiC reinforced Ni-based coating: Process, microstructure and properties. In: Ceramics Internationa, Vol. 47, No. 21, pp. 30113-30128.
Go to original source...
- SHU, D., CUI, X., LI, Z. (2020). Effect of the rare earth oxide CeO2 on the microstructure and proper-ties of the nano-WC-reinforced Ni-based composite coating. In: Metals, Vol. 10, No. 3, pp. 383.
Go to original source...
- LEUNDA, J., SANZ, C., SORIANO, C. (2016). Laser cladding strategies for producing WC reinforced NiCr coatings inside twin barrels. In: Surface and Coatings Technology, Vol. 307, No. 3, pp. 720-727.
Go to original source...
- LEI, J., SHI, C., ZHOU, S. (2018). Enhanced corrosion and wear resistance properties of carbon fiber re-inforced Ni-based composite coating by laser cladding. In: Surface and Coatings Technology, Vol. 334, No. 2, pp. 274-285.
Go to original source...
- SHI, C., LEI, J., ZHOU, S. (2018). Microstructure and mechanical properties of carbon fibers strengthened Ni-based coatings by laser cladding: The effect of carbon fiber contents. In: Journal of Alloys and Compounds, Vol. 744, No. 2, pp. 146-155.
Go to original source...
- YANG, G., XIE, Y., ZHAO, S., ET al. (2022). Methods and mechanism of powder mixing for selective laser melting. In: Manufacturing Technology, Vol. 22, No. 1, pp. 102-110.
Go to original source...
- GUO, S., YU, J., CUI, L. (2021). Numerical simulation and experimental investigation of coaxiality change of laser cladding rotor shaft. In: Optical Engineering, Vol. 60, No. 12, pp. 124106.
Go to original source...
- MRÁZEK, M., SEDLÁČEK, F., SKOVAJSA, M. (2020). Design of composite disc spring for automotive suspension with using numerical simulation. In: Manufacturing Technology, Vol. 20, No. 4, pp. 525-531.
- LI, C., YU, Z., GAO, J. (2019). Numerical simulation and experimental study of cladding Fe60 on an ASTM 1045 substrate by laser cladding. In: Surface and Coatings Technology, Vol. 357, No. 2, pp. 965-977.
Go to original source...
- CUI, L.J., ZHANG S.H., GUO, S. (2019). Temperature field simulation and experimental analysis of laser cladding 45 steel. In: Optics & Laser Technology, Vol. 57, No. 12, pp. 11-17.
Go to original source...
- LINSEN, S., JIASHENG, W., HAIQING, B., YAJUAN, H. (2019). Numerical and experimental investigation on laser cladding treatment of wear shaft surface. In: Chinese Journal of Mechanical Engineering, Vol. 55, No. 9, pp. 217-223.
Go to original source...
- KOREČEK, D., SOLFRONK, P., SOBOTKA, J. (2020). Numerical simulation as a tool to predict sheet metal forming process of TRIP Steel HCT690. In: Manufacturing Technology, Vol. 20, No. 5, pp. 625-631.
Go to original source...
- HUTASOIT, N., LUZIN, V., BLICBLAU, A. (2015). Fatigue life of laser clad hardfacing alloys on AISI 4130 steel under rotary bending fatigue test. In: International Journal of Fatigue, Vol. 72, No. 1, pp. 42-52.
Go to original source...
- CUI, Z., HU, X., DONG, S. (2020). Numerical simulation and experimental study on residual stress in the curved surface forming of 12CrNi2 alloy steel by laser melting deposition. In: Materials, Vol. 13, No. 19, pp. 4316.
Go to original source...
- NAZEMI, N., URBANIC, J., ALAM, M. (2017). Hardness and residual stress modeling of powder injection laser cladding of P420 coating on AISI 1018 substrate. In: The International Journal of Advanced Man-ufacturing Technology, Vol. 93, No. 9, pp. 3485-3503.
Go to original source...
- KHARROUBI, F., FERTAT, M., EL, HASSANI, S., ET AL. (2021). Simulation and control of a marine ship model's diesel engine using Python and Matlab/Simulink[J]. In: Manufacturing Technology, Vol. 21, No. 4, pp. 483-491.
Go to original source...
- SHAO, Y.P., XU, P., TIAN, J.Y. (2021). Numerical simulation of the temperature and stress fields in Fe-Based alloy coatings produced by wide-band laser cladding. In: Metal Science and Heat Treatment, Vol. 63, No. 5, pp. 327-333.
Go to original source...
- YONG, H., WENLEI, S., YING, C. (2017). Trajectory planning of laser cladding remanufacturing for complex shaft shaped part. In: Infrared and Laser Engineering, Vol. 46, No. 5, pp. 1327-133.
Go to original source...
- HUI, F., JIANFENG, LI., JIE S. (2014). Numerical simulation of the temperature and stress fields in Fe-Based alloy coatings produced by wide-band laser cladding. In: Chinese Journal of Lasers, Vol. 41, No. 8, pp. 86-91.
- LIU, L., YANG, X. (2011). Path planning of laser remanufacturing robot based on reverse engineering. In: Chinese Journal of Lasers, Vol. 38, No. 7, pp. 0703008-4.
Go to original source...
- WANG, X., SUN, W., CHEN, Y. (2018). Research on trajectory planning of complex curved surface parts by laser cladding remanufacturing. In: The International Journal of Advanced Manufacturing Tech-nology, Vol. 96, No. 5, pp. 2397-2406.
Go to original source...
- LI, Y., DONG, S., YAN, S. (2018). Surface remanufacturing of ductile cast iron by laser cladding Ni-Cu alloy coatings. In: Surface and Coatings Technology, Vol. 347, No. 1, pp. 20-28.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.