Manufacturing Technology 2023, 23(6):927-934 | DOI: 10.21062/mft.2023.078

Optimization of Threads Production on Thin – Walled Castings

Dana Stančeková ORCID...1, Jozef Mrázik ORCID...1, Anna Rudawska ORCID...2, Miroslava Ťavodová ORCID...3, Izabela Miturska-Barańska ORCID...2, Daniela Sršníková1, Miroslav Špiriak1
1 Faculty of Mechanical Engineering, University of Žilina, Univerzitná 1, 010 26, Žilina. Slovak Republic
2 Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland
3 Faculty of Technology, Technical University in Zvolen, Študentská 26, 960 53. Slovak Republic

This study focuses on the analysis and solution of thread production in thin-walled profiles. It explores three different threading technologies, including cutting, forming, and extrusion. The issue of a screw joint in a thin-walled component is complex due to the stiffness of the joint and the short length of the thread. Hence, the careful choice of a suitable manufacturing process for producing inner threads in thin-walled components holds significant importance. The study entails monitoring the hardening of surface layers of materials after thread production, in conjunction with the acquisition of microstructure images of the experimental material. The outcome is a comparative evaluation of different individual thread production technologies.

Keywords: Thread cutting, Thread forming, Thread pressing, Thin-walled profile
Grants and funding:


The article was created as part of the support of the grant project KEGA 015ŽU-4/2023 "Modernization of teaching chip technologies with elements of information technology based on networked virtual laboratories"

Received: July 30, 2023; Revised: October 9, 2023; Accepted: October 26, 2023; Prepublished online: November 27, 2023; Published: December 22, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Stančeková D, Mrázik J, Rudawska A, Ťavodová M, Miturska-Barańska I, Sršníková D, Špiriak M. Optimization of Threads Production on Thin – Walled Castings. Manufacturing Technology. 2023;23(6):927-934. doi: 10.21062/mft.2023.078.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BRANDÃO, G.L., CARMO SILVA, P.M., FREITAS, S.A., PEREIRA, R.B.D., LAURO, C.H., BRANDÃO, L.C. (2020) State of the art on internal thread manufacturing: a review. The International Journal of Advanced Manufacturing Technology, 110:3445-3465; https://doi.org/10.1007/s00170-020-06107-x Go to original source...
    2. HEILER, R. (2018) Cold thread Forming - the chipless alternative for high resistant internal threads. MATEC Web of Conferences, 251, 02046 Go to original source...
    3. CHAKHARI, J., DAIDIÉ, A.; CHAIB, Z.; GUILLOT, J. (2008) Numerical model for two-bolted joints subjected to compressive loading. Finite Elem. Anal. Des., 44, 162-173. Go to original source...
    4. FRYDRÝŠEK, K.; ŠÍR, M.; PLEVA, L.; SZELIGA, J.; STRÁNSKÝ, J.; ČEPICA, D.; KRATOCHVÍL, J.; KOUTECKÝ, J.; MADEJA, R.; DEDKOVÁ, K.P.; ET AL. (2022) Stochastic Strength Analyses of Screws for Femoral Neck Fractures. Appl. Sci. 12, 1015. https://doi.org/10.3390/app12031015 Go to original source...
    5. CORIA, I. ABASOLO, M., AGUIRREBEITIA, J., HERAS, I. (2020) Study of bolt load scatter due to tightening sequence, Int. J. Press Vessels Pip 182, 104054 Go to original source...
    6. BHATTACHARYA, A., SEN, A., DAS, S. (2010) An investigation on the anti-loosening characteristics of threaded fasteners under vibratory conditions. Mech. Mach. Theory 45, 1215-1225, Go to original source...
    7. CORIA, I. MARTÍN, A.H. BOUZID, I. HERAS, M. ABASOLO (2018) Efficient assembly of bolted joints under external loads using numerical FEM. Int. J. Mech. Sci. 142-143, 575-582 Go to original source...
    8. PANJA, B., DAS, S. (2017) Development of an anti-loosening fastener and comparing its performance with different other threaded fasteners, Sa¯dhana¯ Vol. 42, No. 10, pp. 1793-1801_Indian Academy of Sciences DOI 10.1007/s12046-017-0719-4 Go to original source...
    9. STRIZHAK, V., PENKOV, I. (2000) International Symposium on History of Machines and Mechanisms Proceedings HMM 2000 Distribution of axial load on bolt and nut threads, Springer-Science+Business Media Go to original source...
    10. CROCCOLOA, D., AGOSTINISA, M., FINIA, S., OLMIA, G., VINCENZIB, F.R.N. (2019) Steel screws on aluminium nuts: Different engagement ratio tapped threads compared to threaded inserts with a proper tolerance choice. Tribology International 138, 297-306. https://doi.org/10.1016/j.triboint.2019.06.001 Go to original source...
    11. ANNA, C.A., GUILLAUME, F., GÉRARD, P. (2013) Analytical and Experimental Investigations on Thread Milling Forces in Titanium Alloy. Int. J. Mach. Tools Manuf., 67, 28-34. Go to original source...
    12. REJZEK, M., JERSÁK, J., VOTOČEK, J. (2016) The Influence of Process Fluids on the Machining Process and Forming Internal Threads. In. Manufacturing Technology, 16(4):793-799, DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/4/793 Go to original source...
    13. JIANLI, S., ZHIQI, L., YONGTANG, L., (2017), Cold Rolling Precision Forming of Shaft Parts. Theory and technologies, Springer-Verlag, Berlin Heidelberg. http://dx. doi.org/10.1007/978-3-662-54048-0. Go to original source...
    14. TALU, Ş., (2019) Thread Rolling Technology. Napoca Star Publishing House, Cluj- Napoca, Romania. ISBN 978-606-690-890-0.
    15. TALU, S., SAGLAMB, H., KUSB, R., BRAMOWICZC, M., KULESZAD, S. (2020) Experimental investigations of threads surface integrity manufactured by cutting insert and with internal thread rolling head. CIRP Journal of Manufacturing Science and Technology 31, 334-341. https://doi.org/10.1016/j.cirpj.2020.06.007 Go to original source...
    16. ELSHENNAWY, A.K., WEHEBA, G.S., (2015) Manufacturing Processes & Materials. 5th ed. Society of Manufacturing Engineers, Dearborn, Michigan, USA.
    17. PATER, Z., GONTARZ, A., WERONSKI, W., (2004), New Method of Thread Rolling. Journal of Material Processing Technology, 153-154/1-3: 722-728. Go to original source...
    18. Heiler, R. (2019) Flow drilling technology and thread forming - an economical and secure connection in hollow sections and thin-walled components. E3S Web of Conferences 97, 06033, (FORM-2019), https://doi.org/10.1051/e3sconf/20199706033 Go to original source...
    19. MIAO, H., SHAN, X., ZHANG, S., JIN, Y., ZUO, D. (2018) Process Online Monitoring on Cold Extrusion of Internal Thread in High-strength Steel. In. Manufacturing Technology, 18(6), 954 - 961 DOI: 10.21062/ujep/207.2018/a/1213-2489/MT/18/6/954 Go to original source...
    20. HAMRAN, M. (2015) Odolnosť vybraných konštrukčných materiálov voči únave. Bachelor thesis. Žilina: UNIZA, 2015. 43 s
    21. Walter GPS. (2022) [online] <http://gps.walter-tools.com/touchtime/walter/#/home
    22. Garant Tool Scout. (2022) [online]. <http://www.toolscout.de/ToolScout/>

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content