Manufacturing Technology 2024, 24(1):110-116 | DOI: 10.21062/mft.2024.017
Heat Treatment of Steel 1.3520: Influence of Temperature and Austenitization Time
- Tomas Bata University in Zlin, Faculty of Technology, Vavreckova 5669, 760 01 Zlin. Czech Republic.
This study deals with influence of temperature and time of austenitization on final mechanical proper-ties, especially hardness, obtained after heat treatment of steel 1.3520. Following process parameters of heat treatment were varied: time of austenitization and type of cooling medium, which has a significant effect on final structure, thus mechanical properties. These parameters were varied according to reccomended range given in material sheet. As can be seen from results, different temperature and time of austenitization influenced final hardness after quenching and tempering. Lower temperature and shorter time of austenitization led to insufficient homogenization of austenite and incomplete transformation to martensite and bainite, which resulted in lower hardness. On the other hand, higher temperature and longer time of austenitization can lead to coarser austenite grain, which can also result in lower hardness.
Keywords: Heat treatment, Hardening, Tempering, Austenitization, Hardness
Grants and funding:
This work was supported by the Internal Grant Agency of TBU in Zlin: no. IGA/FT/2024/003
Received: November 19, 2023; Revised: February 1, 2024; Accepted: February 1, 2024; Prepublished online: February 1, 2024; Published: February 23, 2024 Show citation
References
- TOTTEN, G. E. (2007). Steel heat treatment: metallurgy and technologies. 2nd ed. Boca Raton: CRC/Taylor & Francis. ISBN 9780849384554.
Go to original source...
- LISCIC, BOZIDAR, HANS M. TENSI, LAURALICE C.F. CANALE AND TOTTEN, G.E. (2010) Quenching Theory and Technology. 2nd ed. Boca Raton: CRC Press. ISBN 9781439859865.
Go to original source...
- KHIDHAIR M. (2014) Influence of Heat Treatment on the Mechanical Properties of Steel Type (40X), Modern Methods of Construction Design., pp 83-88.
Go to original source...
- SRIVASTAVA K, SINHA A.A., SAHANI R. (2021) Effect of heat treatment on hardness and toughness of EN8 steel, Materials Today: Proceedings, 42, pp 1297-1303.
Go to original source...
- KLOBÈAR, D., TU©EK, J. AND TALJAT, B. (2008) Thermal fatigue of materials for die-casting tooling, Mater. Sci. Eng., A472, pp. 198 - 207.
Go to original source...
- TUKUR, H. AND YONGHAO, L. (2020) Oxidation and deformation behaviors of the 316L stainless-steel weldments in nuclear plants, Int. J. Electrochem. Sci., Vol. 15, No. 3, pp. 2115-2132.
Go to original source...
- ABE, M. (2021) Research and development trends of stainless steel and its future prospects, Nippon Steel Tech. Rep., No. 126, pp. 2-12.
- LOLLA, T.; COLA, G.; NARAYNANA, B.; ALEXANDROV, B.; BABU, S.S. (2022) Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures. Mater. Sci. Technol., Vol. 27, 863.
Go to original source...
- JÁSZFI, V.; PREVEDEL, P.; EGGBAUER, A.; GODAI, Y.; RANINGER, P.; MEVEC, D.; PANZENBÖCK, M.; EBNER, R. (2019) Influence of the parameters of induction heat treatment on the mechanical properties of 50CrMo4. HTM J. Heat Treat. Mater., Vol. 74, pp. 366-379.
Go to original source...
- EGGBAUER, A.; LUKAS, M.; PREVEDEL, P.; PANZENBÖCK, M.; RESSEL, G.; EBNER, R. (2019) Effect of Initial Microstructure, Heating Rate, and Austenitizing Temperature on the Subsequent For-mation of Martensite and Its Microstructural Features in a QT Steel. Steel Res. Int., Vol. 90, 1800317.
Go to original source...
- ATAY, G.Y.; BILGIC, N. (2023) Investigation of the Microstructure and Mechanical Properties of Heat-Treated 42CrMoS4 Steel. Journal of Materials Engineering and Performance.
Go to original source...
- KOTOUS, J.; SALVETR, P.; NACHÁZELOVÁ, D. (2023) Influence of Structural State prior Quenching in Spring Steel. Manufacturing technology, Vol. 23, pp. 186-193.
Go to original source...
- BRICIN, D.; KRIZ, A.; NOVOTNY, J.; SPIRIT, Z. (2022) The Effect of Boriding and Heat Treatment on the Structure and Properties of 100Cr6 Steel. Manufacturing technology, Vol. 22, pp. 2-9.
Go to original source...
- WENTING, W.; JINZHE, K.; ZHENG, L.; GUOCHENG, L.; QINGLONG, L.; DONGSHENG, Q.; LIN, H. (2023) Understanding the microstructural evolution and fretting wear behaviors of M50 bearing steel heat treated at different temperatures. Journal of Materials Research and Technology, Vol. 27, pp. 6661-6671.
Go to original source...
- SHEN, J.; LEI, S.; FANG, J.; LIU, Y.; HU, Z.; CUI, S.; ZHANG, H.; XUE, Z. (2023) Effect of High Temperature Heat Treatment on the Structure and Properties of FeCoCrNiZr Alloy. Manufacturing technology, Vol. 23, pp. 326-332.
Go to original source...
- BURDOVA, K.; JIRKOVA, H.; KUCEROVA, L.; ZETKOVA, I.; MACH. J. (2022) Effects of Heat Treatment on Additively Manufactured 316L Stainless Steel. Manufacturing technology, Vol. 22, pp. 261-266.
Go to original source...
- HREN, I.; KUSMIERCZAK, S.; HORKY, R.; MACH, J. (2022) Analysis of the Effect of Heat Treatment and Corrosion Load on the Microstructure and Microhardness of the Ti6Al4V Alloy. Manufacturing technology, Vol. 22, pp. 414-422.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.