Manufacturing Technology 2024, 24(1):104-109 | DOI: 10.21062/mft.2024.008

How to Determine Possible Interactions of Silicide and Aluminide in Preparation of Composites

Pavel Novak ORCID...1, Stanislav Mestek ORCID...1, Alena Michalcová ORCID...1, Alisa Tsepeleva ORCID...1, Kateřina Skotnicová ORCID...2, Ivo Szurman ORCID...2
1 Department of Metals and Corrosion Engineering, University of Chemistry and Technology, Prague, Technická 5, 166 28 Prague 6, Czech Republic
2 Department of Materials and Technologies for Vehicles, Faculty of Materials Science and Technology, VSB-Technical University of Ostrava, 17. listopadu 15, 70800 Ostrava-Poruba, Czech Republic

Silicide – aluminide composites could be considered as potential tool materials, because of high wear resistance and thermal stability. Recently, the alloys based on iron aluminide and silicide were tested, but they found to be very brittle due to the occurrence of brittle Fe-Al-Si ternary phases. On the other hand, in TiAl-Ti5Si3 composite, no ternary phase was formed during sintering, even though it can be expected based on thermodynamics. Therefore, this paper aims on finding the way how to test poten-tial interaction between silicide and aluminide phase during preparation of these composites.

Keywords: Aluminide, Silicide, Sintering, Reaction
Grants and funding:

This research was financially supported by Czech Science Foundation, project No. 23-05126S

Received: August 31, 2023; Revised: January 4, 2024; Accepted: January 4, 2024; Prepublished online: January 8, 2024; Published: February 23, 2024  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Novak P, Mestek S, Michalcová A, Tsepeleva A, Skotnicová K, Szurman I. How to Determine Possible Interactions of Silicide and Aluminide in Preparation of Composites. Manufacturing Technology. 2024;24(1):104-109. doi: 10.21062/mft.2024.008.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. GRILLI, M.L., VALERINI, D., SLOBOZEANU, A.E., POSTOLNYI, B.O., BALOS, S., RIZZO, A., PITICESCU, R.R. (2021) Critical Raw Materials Saving by Protective Coatings under Extreme Conditions: A Review of Last Trends in Alloys and Coatings for Aerospace Engine Applications. In: Materials, Vol. 14, 1656. ISSN 1996-1944. Go to original source...
    2. PRŮCHA, V, BRICÍN, D, KŘÍ®, A. (2019) Effect of Cryogenic Treatment on Properties of Cemented Carbides. In: Manufacturing Technology. Vol 19, pp. 129-134. ISSN 1213-2489. Go to original source...
    3. SRAMHAUSER K, NAPRSTKOVA N, HREN I, SPALEK F, VLACH T, KUNES R, TUPY O. (2023) Wear Analysis of Indexable Inserts after Machining of Austenitic Steel 1.4404. In: Manufacturing Technology. Vol. 23, No. 6, pp. 917-926. ISSN 1213-2489. Go to original source...
    4. RIZZO, A., GOEL, S., LUISA GRILLI, M., IGLESIAS, R., JAWORSKA, L., LAPKOVSKIS, V., NOVAK, P., POSTOLNYI, B.O., VALERINI, D. (2020) The Critical Raw Materials in Cutting Tools for Machining Applications: A Review. In: Materials, Vol. 13, 1377. ISSN 1996-1944. Go to original source...
    5. WALUNJ, G., BEARDEN, A., PATIL, A., LARIMIAN, T., CHRISTUDASJUSTUS, J., GUPTA, R.K., BORKAR, T. (2020) Mechanical and Tribological Behavior of Mechanically Alloyed Ni-TiC Composites Processed via Spark Plasma Sintering. In: Materials, Vol. 13, 5306. ISSN 1996-1944. Go to original source...
    6. ©VEC, P, GÁBRI©OVÁ, Z, BRUSILOVÁ, A. (2020) Hot Pressing of Boron Carbide Based Ceramic Com-posites. In: Manufacturing Technology. Vol. 20, No. 3, pp. 394-400. ISSN 1213-2489. Go to original source...
    7. KNAISLOVÁ, A., NOVÁK, P., PRŮ©A, F. (2016) Preparation of Ti-Al-Si Alloys by Powder Metallurgy. In: Manufacturing Technology, Vol. 16, No. 6, pp. 1274-1278. ISSN 1213-2489. Go to original source...
    8. NOVÁK, P., NOVÁ, K., VANKA, T., PRŮ©A, F. (2018) High-temperature Behaviour of New Fe-Al-Si Alloy Produced by Powder Metallurgy. In: Manufacturing Technology, Vol. 18, No. 2, pp. 299-302. ISSN 1213-2489. Go to original source...
    9. NOVÁK, P., MESTEK, S., MICHALCOVÁ, A., SKOTNICOVÁ, K., SZURMAN, I. (2023) Preparation of NiAl-FeSi composites by powder metallurgy. In: Metal 2023 conference proceedings, Tanger, Ostrava, paper E11. Go to original source...
    10. MEHRER, H. EGGERSMANN, M., GUDE, A., SALAMON, M., SEPIOL, B. (1997) Diffusion in inter-metallic phases of the Fe-Al and Fe-Si systems. In: Materials Science and Engineering: A, Vol. 239-240,pp. 889-898, ISSN 0921-5093. Go to original source...
    11. MASSALSKI, T.B. (1990) Binary alloy phase diagrams, ASM International, Materials Park, Ohio, ISBN 9780871704030.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content