Manufacturing Technology 2024, 24(2):289-293
The Effect of Strain Rate on the Friction Coefficient
- Brno University of Technology, Faculty of Mechanical Engineering, Institute of Manufacturing Technology, Department Metal Forming and Plastics, Technická 2896/2, 616 69 Brno, Czech Republic
The Male and Cockroft ring compression test is one of the methods used to determine the coefficient of friction in forming. This method can be used to determine the coefficient of friction without the need to measure the force. This paper describes the results of the Male and Cockroft ring compres-sion test for the Hardox 450 material at different strain rates. The experiment was performed on ZD40 hydraulic press and CFA-80 pneumatic die hammer at the Faculty of Mechanical Engineering of Brno University of Technology. The test results were recorded in a calibration diagram. The results show that the strain rate has a significant effect on the coefficient of friction, specifically such that as the strain rate increases, the coefficient of friction decreases.
Keywords: Strain rate, Friction, Calibration diagrams, Ring compression test, Hardox 450 steel
Received: December 12, 2023; Revised: March 15, 2024; Accepted: March 20, 2024; Prepublished online: March 20, 2024; Published: April 30, 2024 Show citation
References
- JOUN, M.S.; MOON, H.G.; CHOI, I.S.; LEE, M.C. a JUN, B.Y. Effects of friction laws on metal forming processes. Tribology International. 2009, Volume 42, Issue 2, Pages 311-319. ISSN 0301-679X.
Go to original source...
- KUNOGI, Mahito. A New Method of Cold Extrusion. Transactions of the Japan Society of Mechanical Engineers. 1957, Volume 23, Issue 134, Pages 742-749. Available from: https://doi.org/10.1299/kikai1938.23.742.
Go to original source...
- MALE, A. and COCKROFT, M., 1965/01/01. A Method for the Determination of Coefficient of Friction of Metals under Condition of Bulk Plastic Deformation. Journal of Institute of Metals. Volume 93, Pages 38 46.
- CAMACHO, A.M.; TORRALVO, A.I.; BERNAL, C. and SEVILLA, L., 2013. Investigations on Friction Factors in Metal Forming of Industrial Alloys. Procedia Engineering. Volume 63, Pages 564-572. Available from: https://doi.org/10.1016/j.proeng.2013.08.240.
Go to original source...
- WANG, Wen and ZHOU, Xiang, 2023. Temperature-dependent friction coefficient on flat graphite plane. Surface Science. Volume 729, Pages 122-233. Available from: https://doi.org/10.1016/j.susc.2022.122233.
Go to original source...
- JOPEK, Miroslav, 2021. Determination of Carbon Steel Dynamic Properties. Manufacturing Technology, Volume 21, Issue 4, pages 479-482. Available from: https://doi.org/10.21062/mft.2021.061.
Go to original source...
- GIULIANO, Gillo; PARODO, Gianluca; POLINI, Wilma and SORRENTINO, Luca, 2023. Cold Blow Forming of a Thin Sheet in AA8006 Aluminum Alloy. Manufacturing Technology, Volume 23, Issue 3, pages 284-289. Available from: https://doi.org/10.21062/mft.2023.038.
Go to original source...
- VILIS, Jindrich; POKORNY, Zdenek; ZOUHAR, Jan and JOPEK, Miroslav, 2022. Ballistic Resistance of Composite Materials Tested by Taylor Anvil Test. Manufacturing Technology, Volume 22, Issue 5, pages 610-616. Available from: https://doi.org/10.21062/mft.2022.074.
Go to original source...
- LIPIÑSKI, Tomasz. Influence of Impurity Morphology on the Fatigue Strength of High-Purity Structural Steel Melted in an Electric Furnace, 2023. Manufacturing Technology. Volume 23, Issue 1, pages 53-59. Available from: https://doi.org/10.21062/mft.2023.001.
Go to original source...
- SVOBODA, Petr, JOPEK, Miroslav, SVOBODA, Ondøej and Martin HARANT. DETERMINATION OF DYNAMIC PROPERTIES OF 3D PRINTED G3SI1 STEEL, 2024. MM Science Journal. Volume 16, Issue 2, pages 7230-7233. Available from: https://doi.org/ 10.17973/MMSJ.2024_03_2021183.
Go to original source...
- CAMACHO, A.M.; TORRALVO, A.I.; BERNAL, C. and SEVILLA, L., 2013. Investigations on Friction Factors in Metal Forming of Industrial Alloys. Procedia Engineering. Volume. 63, Pages. 564-572. Available from: https://doi.org/10.1016/j.proeng.2013.08.240.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.