Manufacturing Technology 2024, 24(3):333-337 | DOI: 10.21062/mft.2024.042

Investigation of Printing Speed Impact on the Printing Accuracy of Fused Filament Fabrication (FFF) ABS Artefacts

Vasiliki E. Alexopoulou ORCID...1, Ioannis T. Christodoulou ORCID...1, Angelos P. Markopoulos ORCID...1,2
1 Laboratory of Manufacturing Technology, School of Mechanical Engineering, National Technical University of Athens, 15780 Zografou, Greece
2 AGH University of Krakόw, Department of Manufacturing Systems, Faculty of Mechanical Engineering and Robotics, 30-059 Krakow, Poland

This paper introduces a customized Fused Filament Fabrication (FFF) printer, featuring an advanced electromechanical system that achieves a substantial 500% increase in printing speed compared to con-ventional FFF printers. This research scrutinizes the printer's capabilities, emphasizing the dimension-al accuracy. Specifically, this study focuses on the investigation of the effect of high printing speeds on the dimensional accuracy of linear artifacts. The material selected is Acrylonitrile Butadiene Styrene (ABS) and the FFF-fabricated parts are designed and measured based on the ISO ASTM 52902-2021 standard. Last but not least, statistical analysis and comments are following, showing remarkable re-sults on such high-speeds.

Keywords: High-Speed Fused Filament Fabrication, Printing Speed, Dimensional Accuracy, ABS

Received: January 2, 2024; Revised: April 2, 2024; Accepted: May 9, 2024; Prepublished online: May 16, 2024; Published: July 1, 2024  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Alexopoulou VE, Christodoulou IT, Markopoulos AP. Investigation of Printing Speed Impact on the Printing Accuracy of Fused Filament Fabrication (FFF) ABS Artefacts. Manufacturing Technology. 2024;24(3):333-337. doi: 10.21062/mft.2024.042.
Download citation

References

  1. O. A. MOHAMED, S. H. MASOOD, and J. L. BHOWMIK, "Optimization of fused deposition modeling process parameters: a review of current research and future prospects," Adv. Manuf., vol. 3, no. 1, pp. 42-53, 2015, doi: 10.1007/s40436-014-0097-7. Go to original source...
  2. S. VYAVAHARE, S. TERAIYA, D. PANGHAL, and S. KUMAR, "Fused deposition modelling: a review," Rapid Prototyp. J., vol. 26, no. 1, pp. 176-201, 2020, doi: 10.1108/RPJ-04-2019-0106. Go to original source...
  3. K. RAJAN, M. SAMYKANO, K. KADIRGAMA, W. S. W. HARUN, and M. M. RAHMAN, Fused deposition modeling: process, materials, parameters, properties, and applications, vol. 120, no. 3-4. Springer London, 2022. doi: 10.1007/s00170-022-08860-7. Go to original source...
  4. J. YANG and Y. LIU, "Energy, time and material consumption modelling for fused deposition modelling process," Procedia CIRP, vol. 90, no. March, pp. 510-515, 2020, doi: 10.1016/j.procir.2020.02.130. Go to original source...
  5. A. BOSCHETTO and L. BOTTINI, "Accuracy prediction in fused deposition modeling," Int. J. Adv. Manuf. Technol., vol. 73, no. 5-8, pp. 913-928, 2014, doi: 10.1007/s00170-014-5886-4. Go to original source...
  6. P. CZYŻEWSKI, D. MARCINIAK, B. NOWINKA, M. BOROWIAK, and M. BIELIŃSKI, "Influence of Extruder's Nozzle Diameter on the Improvement of Functional Properties of 3D-Printed PLA Products," Polymers (Basel)., vol. 14, no. 2, 2022, doi: 10.3390/polym14020356. Go to original source...
  7. J. F. CHAUVETTE, D. BRZESKI, I. L. HIA, R. D. FARAHANI, N. PICCIRELLI, and D. THERRIAULT, "High-speed multinozzle additive manufacturing and extrusion modeling of large-scale microscaffold networks," Addit. Manuf., vol. 47, no. June, p. 102294, 2021, doi: 10.1016/j.addma.2021.102294. Go to original source...
  8. R. J. A. ALLEN and R. S. TRASK, "An experimental demonstration of effective Curved Layer Fused Filament Fabrication utilising a parallel deposition robot," Addit. Manuf., vol. 8, pp. 78-87, 2015, doi: 10.1016/j.addma.2015.09.001. Go to original source...
  9. I. CHRISTODOULOU, "Study and Development of a High-Speed Fused Filament Fabrication 3D Printer".
  10. K. M. AGARWAL, P. SHUBHAM, D. BHATIA, P. SHARMA, H. VAID, and R. VAJPEYI, "Analyzing the Impact of Print Parameters on Dimensional Variation of ABS specimens printed using Fused Deposition Modelling (FDM)," Sensors Int., vol. 3, no. November 2021, p. 100149, 2022, doi: 10.1016/j.sintl.2021.100149. Go to original source...
  11. V. E. ALEXOPOULOU, I. T. CHRISTODOULOU, and A. P. MARKOPOULOS, "Effect of Printing Speed and Layer Height on Geometrical Accuracy of FDM-Printed Resolution Holes of PETG Artifacts †," 2022. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.