Manufacturing Technology 2024, 24(3):448-457 | DOI: 10.21062/mft.2024.044
Experimental Study of Tool Life Depending on Cutting Speed for 100CrMn6 Materials & Statistical Processing Using Linear Regression Analysis
- Faculty of Special Technology, Alexander Dubcek University of Trenčín, Ku Kyselke 469, 911 06 Trenčín, Slovakia
To increase the service life of the cutting tool, various types of coatings are used in modern times, which have a beneficial effect on extending the service life of the tools. Which contributes to reducing the eco-nomic costs of production. The present article examines the effect of cutting speed on the durability of a cutting tool. In the experimental measurements, three types of replaceable cutting inserts were used, without coating, with TiC and TiN coating. The measurements were carried out during technological operations of longitudinal turning on bearing steel 100CrMn6 without the use of coolant. The durability of the cutting discs was evaluated by the method of short-term tests, in which the main evaluation crite-rion was the amount of wear on the back surface of the cutting tool VBBcrit = 0.25 mm. For the statistical processing of the measured results, a detailed mathematical calculation was performed using the meth-od of least squares to determine the parameters of the linear regression function.
Keywords: Durability, Wear, Cutting Speed, Turning, Coating
Received: January 22, 2024; Revised: April 18, 2024; Accepted: May 9, 2024; Published: July 1, 2024 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- PANDA, A., DUPLÁK, J., JURKO, J., BEHÚN, M. (2011). Comprehensive Identification of Sintered Car-bide Durability in Machining Process of Bearings Steel 100CrMn6. In: Advanced Materials Research, Vol. 340, pp. 30 - 33. ISSN 1662-8985.
Go to original source...
- VASILKO, K., MURČINKOVÁ, Z. (2015). Question of Optimal Cutting Speed for Machining by Conventional and Coated Cutting Tools. In: Manufacturing Technology, Vol. 15, No. 3, pp. 483 - 490.
Go to original source...
- VASILKO, K. (2017). Taylor Equation of Durability and Its Modification. In: Manufacturing Technology, Vol. 17, No. 3, pp. 393 - 397.
Go to original source...
- KORKOMAZ, M. E., GUPTA, M. K., Çelik, E., ROSS, N. S., Günay, M. (2024). Tool wear and its mechanism in turning aluminum alloys with image processing and machine learning methods. In: Tribology Internation-al, Vol. 191. Elsevier Publisher, ISSN 0301679X.
Go to original source...
- BOUZID SAI, W. (2005). An investigation of tool wear in high-speed turning of AISI 4340 steel. In: Interna-tional Journal of Advanced Manufacturing Technology, Vol. 23, pp. 330 - 334.
Go to original source...
- GASNER, M., SCHALK, N., TKADLETZ, M., POHLER. M., CZETTL, CH., MITTERER, CH. (2018). Influence of cutting speed and workpiece material on the wear mechanisms of CVD TiCN/α-Al2O3 coated cutting inserts during turning. In: Wear, Vol. 398-399, pp. 90 - 98.
Go to original source...
- RANJAN DAS, R., PANDA, A., DHUPAL D. (2017). Experimental investigation of surface roughness, flank wear, chip morphology and cost estimation during machining of hardened AISI 4340 steel with coated carbide insert. In: Mechanics of Advanced Materials and Modern Processes, Vol. 3, No. 9.
Go to original source...
- FARAHNAKIAN, M., KESHAVARZ, E. M., ELHAMI, S., MOHAMMAD, R. M. (2016). Effect of cutting edge modification on the tool flank wear in ultrasonically assisted turning of hardened steel. In: Institution of Mechanical Engineers, Vol. 233, No. 5.
Go to original source...
- MAJERÍK, J., BARÉNYI, I., SEDLÁK, J. (2019). Investigation of flank wear when finish turning of high strength steel with CBN cutting insert. In: Annals of DAAAM International, Vol. 30, No. 1, ISSN 1726-9679.
Go to original source...
- MOTORCU, A. R. (2011). Tool life performances, wear mechanisms and surface roughness characteristics when turning austenised and quenched AISI 52100 bearing steel with ceramics and CBN/TiC cutting tools. In: Indian Journal of Engineering and Materials Sciences, Vol. 18, No. 2, pp. 137-146.
Go to original source...
- ZHENG, G., XU, R., CHENG, X., ZHAO, G., LI, L., ZHAO, J. (2011). Effect of cutting parameters on wear behavior of coated tool and surface roughness in high-speed turning of 300M. In: Measurement, Vol. 125, pp. 99-108.
Go to original source...
- THAMIZHMNAII, S., BIN OMAR, B., SAPARUDIN, S., HASAN, S. (2008). Tool flank wear analyses on martensitic stainless steel by turning. In: Archives of Materials Science and Engineering, Vol. 32, No. 1, pp. 41 - 44.
- KUNDRÁK, J., PÁLMAI, Z. (2019). The Change of Tool Life in a Wide Range of Cutting Speeds in Hard Turning. In: Manufacturing Technology, Vol. 19, No. 2, pp. 245 - 260.
Go to original source...
- SRAMHAUSER, K., NAPRSTKOVA, N., Hren, I., SPALEK, F., VLACH, T., KUNES, R., TUPY, O. (2023). Wear Analysis of Indexable Inserts after Machining of Austenitic Steel 1.4404. In: Manufacturing Technology, Vol. 23, No. 6, pp. 917 - 926.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.