Manufacturing Technology 2013, 13(2):210-215 | DOI: 10.21062/ujep/x.2013/a/1213-2489/MT/13/2/210

Differences at the Surface Roughness by the ELID and Grinding Technology

Martin Novak1, Hiroshi Kasuga2, Hitoshi Ohmori2
1 Faculty of Production Technology and Management, J. E. Purkyne University in Usti nad Labem. Czech Republic. Europe
2 Materials Fabrication Laboratory, RIKEN, Wako-shi, Tokyo, Japan

This paper deals with surface roughness and surface profile in high precision methods of materials finishing. One of them is ELID grinding process and the second method is fine grinding. There is surface profile and roughness compared of the three materials samples - carbide steel and two aluminium alloys. In the paper are shown the principle of the ELID grinding and fine grinding, results of surface measurement between ELID and ground surface. Both methods are very precision in the focus on surface roughness - measured units in nano scale. The paper shows also real topology of the surfaces and visible tool marks especially by the fine grinding method. Next we can see new possibilities in finishing methods for different areas of the production, automotive, aerospace, medicine and cosmic industry.

Keywords: ELID, Fine Grinding, Roughness, Tool Marks, Surface profile

Published: June 1, 2013  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Novak M, Kasuga H, Ohmori H. Differences at the Surface Roughness by the ELID and Grinding Technology. Manufacturing Technology. 2013;13(2):210-215. doi: 10.21062/ujep/x.2013/a/1213-2489/MT/13/2/210.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. KOCMAN, K. 2010. Analyza vyvojovych brousicich kotoucu na bazi mikrokrystalickeho korundu, Strojirenska technologie, vol. XV, no. 3, UJEP, Usti nad Labem, 40-47 pp.
    2. LUKOVICS, I., BILEK, O., HOLEMY, S. 2010. Development of Grinding Wheels for Tools Manufacturing, Manufacturing Technology, vol. 10, no. 10, UJEP, Usti nad Labem, 10-16 pp. Go to original source...
    3. MARINESCU, I., D., et all. 2007. Handbook of Machining with Grinding wheels, Boca Raton: CRC Press, 592 pp. Go to original source...
    4. NOVAK, M. 2011. Surface quality of hardened steels after grinding. Manufacturing Technology, vol. 11, no. 11, UJEP, Usti nad Labem, 55-59 pp. Go to original source...
    5. KUNDRAK, J. 2011. Alternative machining procedures of hardened steels, Manufacturing Technology, vol. 11, no. 11, UJEP, Usti nad Labem, 32-39 pp. Go to original source...
    6. NOVAK M., LATTNER M., RUZICKA L., HOLESOVSKY F., 2010. Grinding and surface quality parameters at automotive parts machining, Manufacturing Technology, vol. 10, no. 10, UJEP, Usti nad Labem, 36-38 pp. Go to original source...
    7. HOLESOVSKY, F., NOVAK, M. 2010. Grinding and its influence to ground surface durability. Proceedings of International Conference on Advances in Materials and Processing Technologies, Paris. Publisher: Amer INST Physics, Melville, NY, USA. ISBN 978-0-7354-0871-5. WOS: 000287169300158.
    8. NOVAK, M. 2012. Influence of the Corrosion Surrounding on Surface Quality of Ground Hardened Steels In Key Engineering Materials, vol. 496: Precision Machining IV. TTP, Zurich, 25 - 30 pp., WOS:000302674400005 Go to original source...
    9. NOVAK, M., NAPRSTKOVA, N., RUZICKA. L. 2012. New ways in aluminium alloys grinding. In Key Engineering Materials, vol. 496: Precision Machining IV. TTP, Zurich, 132 - 137 pp. WOS:000302674400023 Go to original source...
    10. BRINKSMEIER, E., MUTLUGÜNES, Y., KLOCKE, F., AURICH, J.C., SHORE, P. & OHMORI, H. 2010, "Ultra-precision grinding", CIRP Annals - Manufacturing Technology, vol. 59, no. 2, pp. 652-671. Go to original source...
    11. INADA, A., MIN, S. & OHMORI, H. 2011, "Micro cutting of ferrous materials using diamond tool under ionized coolant with carbon particles", CIRP Annals - Manufacturing Technology, vol. 60, no. 1, pp. 97-100. Go to original source...
    12. LEE, H., KASUGA, H., OHMORI, H., LEE, H. & JEONG, H. 2011, "Application of electrolytic in-process dressing (ELID) grinding and chemical mechanical polishing (CMP) process for emerging hardbrittle materials used in light-emitting diodes", Journal of Crystal Growth, vol. 326, no. 1, pp. 140-146. Go to original source...
    13. MADL, J. 2012. Surface Properties in Precise and Hard Machining, Manufacturing Technology, vol. 12, no. 13, 158-166 pp. Go to original source...
    14. NOVAK-MARCINCIN, J. TOROK, J. BARNA, J., NOVAKOVA-MARCINCINOVA, L. 2012. Technology of Perspective Scanning Methods for Realization of 3D Models of Manufacturing Devices, Manufacturing Technology, vol. 12, no. 13, 186-191 pp. Go to original source...
    15. VALASEK, P., MULLER, M. 2012. Influence of bonded abrasive particles size on wear of polymeric particle composites based on waste, Manufacturing Technology, vol. 12, no. 13, 268-272 pp. Go to original source...
    16. MICHNA, S., NAPRSTKOVA, N. 2012. Research into the causes cracking of aluminum alloys of Al - Cu during mechanical machining, Manufacturing Technology, vol. 12, no. 12, 47-51 pp. Go to original source...
    17. KUSMIERCZAK, S., NAPRSTKOVA, N., SVOBODOVA, J. 2012. 2012. Evaluation of sheet degradation with surface treatment, Engineering for Rural Development, vol. 11, 32-36 pp.
    18. VARGA, G., KUNDRÁK, J. 2013. Effect of environmentally conscious machining on machined surface quality, Applied Mechanics and Materials 309, pp. 35-42 Go to original source...
    19. KUNDRAK, J., VARGA, G., DESZPOTH, I., MOLNAR, V. 2013. Some aspects of the hard machining of bore holes, Applied Mechanics and Materials 309, pp. 126-132. Go to original source...
    20. VASILKO, K., MACUROVA, A. 2012. Two Locals Extremes of Cutting Speed. Manufacturing Technology, vol. 12, no. 12, 86-89 pp. Go to original source...

    Return to the content