Manufacturing Technology 2016, 16(1):198-204 | DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/1/198

Design of Control Jig for Inserts Measurement

Ivan Mrkvica1, Vojtech Sleha1, Jana Petru1, Miroslav Neslusan2, Jozef Jurko3, Anton Panda3
1 Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. listopadu 15/2172, 708 33 Ostrava-Poruba, Czech Republic
2 Faculty of Mechanical Engineering, Zilina University in Zilina, Univerzitna 1, 010 26 Zilina, Slovakia
3 Faculty of Manufacturing Technologies with a seat in Presov, Technical University of Kosice, Sturova 31, 080 01 Presov, Slovakia

This paper aims to design a control jig for cutting inserts measurement. These inserts are made from standardized inserts by grinding. The control jig is intended to be used on two different types of measuring devices and it has to meet the functional requirements of these devices.The intoduction describes specific functional requirements on the jig, provides information about measuring devices and examples of cutting edges grinded on inserts. Next part describes the design of several variants of jig parts and reasons for their application. Paper is focused specifically on design of jig body variants, description of measuring arm and the way of clamping of inserts in the control jig. The measuring range is described for each of proposed variant. In the closing part of the article particular variants are compared according to their suitability, stability during measuring and range of serviceability for measuring of the inserts.

Keywords: control jig, body, arm, cutting insert

Published: February 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Mrkvica I, Sleha V, Petru J, Neslusan M, Jurko J, Panda A. Design of Control Jig for Inserts Measurement. Manufacturing Technology. 2016;16(1):198-204. doi: 10.21062/ujep/x.2016/a/1213-2489/MT/16/1/198.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MICIETOVA, A., NESLUSAN, M., CILLIKOVA, M. (2013). Influence of surface geometry and structure after non-conventional methods of parting on the following milling operations. In: Manufacturing Technology, Vol. 13, No. 2, pp. 199-204. Go to original source...
    2. PILC, J., VASILKO, K. (2013). Development and applications of a rotating turning tool. In: Manufacturing Technology, Vol. 13, No. 2, pp. 226-231. Go to original source...
    3. CEP, R., JANASEK, A., PETRU, J., CEPOVA, L., CZAN, A., VALICEK, J. (2013). Hard machinable machining of cobalt-based superalloy. In: Manufacturing Technology, Vol. 13, No. 2, pp. 142-147. Go to original source...
    4. WECKENMANN, A., RADHAKRISHNAN, V.P., SCHMITZ, S. (1999). Fringe projection method for measuring geometry and wear of cutting tool inserts. In: Proceedings of ASPE, 14th Annual Meeting Monterey, USA, pp. 473-476.
    5. SCHWENKE, H., NEUSCHAEFER-RUBE, U., PFEIFER, T., KUNZMANN, H. (2002). Optical methods for dimensional metrology. In: CIRP Annals - Manufacturing Technology, Vol. 51, No. 2, pp. 685-699. Go to original source...
    6. LIM, T. Y., RATNAM, M.M. (2014). Measurement of nose radii of multiple cutting tool inserts from scanned images using sub-pixel edge detection. In: Proceedings of 13th International Conference on Control, Automation, Robotics & Vision Marina Bay Sands, Singapore, pp. 100-105.
    7. WECKERMANN, A., NALBANTIC, K. (2003). Precision measurement of cutting tools with two matched optical 3D-sensors. In: CIRP Annals - Manufacturing Technology, Vol. 52, No. 1, pp. 443-446. Go to original source...
    8. LIM, T. Y., RATNAM, M.M. (2014). Edge detection and measurement of nose radii of cutting tool inserts from scaned 2-D image. In: Optics and Lasers in Engineering, Vol. 50, No. 11, pp. 1628-1642. Go to original source...
    9. Monometal nástroje s.r.o. [online]. 2015 [cit. 2015-12-10]. Available: http://www.monometal.com.
    10. Universal measuring device Smart Tcheck [online]. 2015 [cit. 2015-12-10]. Available: http://www.zoller.cz/wp-content/uploads/2014/04/smarTcheck-600.pdf
    11. PC500 Measurement equipment: Detailed Documentation. [online]. 2015 [cit. 2015-12-10]. Available: [http://www.avyac-machines.com/pc500-multicheck-for-england.html].
    12. IPM Measuring Systems: TC-210 [online]. 2015 [cit. 2015-12-10]. Available: [http://www.ipm-measuring.com/english/tc_210.htm].

    Return to the content