Manufacturing Technology 2016, 16(5):933-939 | DOI: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/933

Influences of Holders Speed on the Cutting Edge during Drag Finishing

Ondřej Hronek, Miroslav Zetek, Tomáš Bakša, Pavel Adámek
Laboratory of Experimental Machining, Regional Technological Institute, Univerzitni 8, 306 14 Pilsen, Czech Republic

The article deals with the influence of the holders speed on the final radius size of the cutting edge. The reason why is investigated radius of cutting edge is that its size affects important parameters in machining process. For example, these parameters are geometrical accuracy of machined components, cutting tool life and stability of machining. Futhermore, it is forces on the cutting edge and thermal influence on the tool. In the experiment five variants are used, prepared by drag finishing. The main variable parameter is holder speed. The aim is to confirm or refute the imput idea. This idea is based on the theory, that the higher holders speed will increase the intensity of drag finishing process. The results are measured and analysed on microscope IFM G4.

Keywords: Microgeometry of the cutting edge, Drag finishing, K factor, Surface quality

Published: October 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Hronek O, Zetek M, Bakša T, Adámek P. Influences of Holders Speed on the Cutting Edge during Drag Finishing. Manufacturing Technology. 2016;16(5):933-939. doi: 10.21062/ujep/x.2016/a/1213-2489/MT/16/5/933.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. ČESÁKOVÁ, I., ZETEK, M. DIAGNOSTIKA STAVU ŘEZNÉHO BŘITU PO MIKROÚPRAVÁCH. In Transfer inovácií. Košice: Technická univerzita v Košiciach, 2011. s. 74-78., ISSN: 1337-7094
    2. ČILLIKOVÁ, M., MIČÚCH, M., NESLUŠAN, M., MIČIETOVÁ, A. (2013). Non-destructive micromagnetic evaluation of surface damage after grinding. In: Manufacturing Technology, Vol. 13, No. 2, ISSN 1213 - 2489 Go to original source...
    3. KŘÍŽ, A., Kolařík, K., JANOUŠEK, A., PALÁN, J. (2015). Integrita povrchu ostří nástroje ze slinutého karbidu. Strojírenská technologie - Plzeň 2015 Sborník příspěvků. s.107-113. ISBN 978-80-261-0304-2
    4. MADL, J., RAZEK, V., KOUTNY, V., KAFKA, J. (2013). Surface Integrity in Notches Machining. In: Manufacturing Technology, Vol. 13, No. 2, ISSN 1213 - 2489 Go to original source...
    5. CSELLE, T., CODDET, O., GALAMAND, C., HOLUBAR, P., JÍLEK, M., JÍLEK, J., LUEMKEMANN, A., MORSTEIN, M. TripleCoatings® - A New Generation of PVD-Coatings for Cutting Tools, In Vrstvy a povlaky 2008. Trenčín: Digital Graphic, 2008. S. 9-14. ISBN 978-80-969310-7-1.
    6. BIERMANN D, BASCHIN A. Influence of cutting edge geometry and cutting edge radius on the stability of micromilling processes. In: Production Engineering, 3, Springer Verlag; 2009, p. 375-380 Go to original source...
    7. DENKENA B., LUCAS A., BASSETT, E. Effects of the cutting edge microgeometry on tool wear and its thermomechanical load. In: CIRP Annals - Manufacturing Technlogy, 60(1); 2011, p. 73-76 Go to original source...
    8. KUNDRAK, J., FELHO, C. (2016). 3D Roughness Parameters of Surfaces Face Milled by Special Tools. In: Manufacturing Technology, Vol. 16, No. 3, ISSN 1213 - 2489 Go to original source...
    9. BOUZAKIS, K.-D., et al. Effect of dry micro-blasting on PVD-film properties, cutting edge geometry and tool life in milling. Surface & Coatings Technology. 2009, 204, 6-7, s. 1081-1086 Go to original source...
    10. DENKENA, B., BIERMANN, D. Cutting edge geometries. CIRP Annals - Manufacturing Technology, 2014; 63:631-653. Go to original source...
    11. DENKENA, B., SPENGLER, C. Influence of Different Grinding Processes on Surface and Subsurface Characteristics of Carbide Tools. Key Engineering Materials, 2004; 257-258:195-200 Go to original source...

    Return to the content