Manufacturing Technology 2018, 18(2):285-288 | DOI: 10.21062/ujep/92.2018/a/1213-2489/MT/18/2/285

Dependence of Surface Roughness on Depth of Cut for Aluminum Alloy AlCu4Mg1

Dusan Mital1, Michal Hatala1, Andrej Bernat1, Andrej Czan3, Jaroslav Vybostek1, Nicolae Ungreanu2
1 Faculty of Manufacturing technologies with a seat in Presov, Technical University of Kosice, Bayerova 1 street, 080 01 Presov, Slovakia
2 Universitatea de Nord din Baia Mare, Facultatea de Inginerie, Str. Dr. V. Babes 62A, RO-430083, Maramures, Romania
3 Faculty of Mechanical Engineering at the University of Zilina, Veľký diel, 010 26 Zilina, Slovak Republic

Presented article is focused on evaluating surface quality parameters Rz and Ra after turning made by various cutting conditions. Monitored parameters in experimental part were feed rate, cutting speed and depth of cut. Researching optimal cutting conditions, which sets often affect and increase productivity, quality and precision of manufactured products. Aim of the article is to increase quality of current state, what require long time testing and experiences. Article also presents individual comparing of two selected cutting plates in various cutting conditions, when in conclusion are clearly define results of experiment and requirement for practical using in industry.

Keywords: Lathe, Roughness, Surface Quality, Cutting Plates

Published: April 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Mital D, Hatala M, Bernat A, Czan A, Vybostek J, Ungreanu N. Dependence of Surface Roughness on Depth of Cut for Aluminum Alloy AlCu4Mg1. Manufacturing Technology. 2018;18(2):285-288. doi: 10.21062/ujep/92.2018/a/1213-2489/MT/18/2/285.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. J. ZAJAC, D. MITAL, P. MICHALIK (2014). Verification of process fluids in mass production,in: J. Kundrat, Z. Maros (Eds.), Precision Machining VII Book series: Key Engineering Materials, 2014, pp. 554-559. Go to original source...
    2. I. VOJTKO, V. SIMKULET, P. BARON, et al. (2014). Microstructural Characteristics Investigation of the Chip-Making Process after Machining,in: S. Fabian, T. Krenicky (Eds.), Operation and Diagnostics of Machines and Production Systems Operational States II book series: Applied Mechanics and Materials, 2014, pp. 344-350. Go to original source...
    3. R. CEP,A. JANASEK, J. PETRU, et al. (2014). Surface Roughness after Machining and Influence of Feed Rate on Process,in: J. Kundrat, Z. Maros (Eds.), Precision Machining VII Book Series: Key Engineering Materials, 2014, pp. 341-347. Go to original source...
    4. BOŽEK P, NIKITIN Y, BEZÁK P, FEDORKO G, FABIAN M. (2015). Increasing the production system productivity using inertial navigation in: In MANUFACTURING TECHNOLOGY. 2015. Vol. 15, No. 3 s. 396 - 403. ISSN 1213-2489 Go to original source...
    5. J. ZIVCAK, M. PETRIK, R. HUDAK, et al. (2009). Embedded Tensile Strenght Test Machine FM1000-An Upgrade of Measurement and Control, in: Z. Gosiewski, Z. Kulesza (Eds.), Mechatronic systems and materials III., Book Series: Solid State Phenomena, 2009, pp. 657-662. Go to original source...
    6. J. ZAJAC, D. MITAL, S. RADCHENKO, et al. (2014). Short-term Testing of Cutting Materials Using the Method of Interrupted Cut, in: S. Fabian, T. Krenicky (Eds.), Operation and Diagnostics of Machines and Production Systems Operational States II book series: Applied Mechanics and Materials, 2014, pp. 236-243. Go to original source...
    7. J. KOVAL. Optimalization of Cutting Conditions of Turning (diploma thesis), 2015.
    8. PETRU, J. SCHIFFNER, J. ZLAMAL, T. SADILEK, M. STANCEKOVA, D. (2015). Investigations of Cutting Tool Wear While Machining Inconel 718. In MANUFACTURING TECHNOLOGY. 2015. Vol. 15, No. 3 s. 396 - 403. ISSN 1213-2489 Go to original source...
    9. S. F. KRAR, A. R. GILL, A. R. SMID (2011). Technology of Machine Tools, 7th ed., McGraw-Hill, New York, 2011.
    10. I. MUKHERJEE, P. K. RAY (2006). A review of Optimization Techniques in Metal Cutting Processes, Computer and Indrustrial engineering. 50 (2006) 15-34. Go to original source...
    11. KOURIL K., CEP R., JANASEK A., KRIZ A., STANCEKOVA D. (2014). Surface Integrity at Reaming Operation by MT3 Head. In: Manufacturing technology, Vol. 14, No. 2, pp. 193 - 199, ISSN 1213-2489 Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content