Manufacturing Technology 2018, 18(5):833-838 | DOI: 10.21062/ujep/186.2018/a/1213-2489/MT/18/5/833

Analysis of Integrity of Surface of Hardened Chromium-Nickel Steel after Finishing Grinding

Dana Stancekova1, Michal Šajgalík1, Jozef Mrázik1, Anna Rudawska2, Miroslav Janota1
1 University of Zilina, Faculty of Mechanical Engineering, Univerzitna 1, 010 26, Zilina, Slovak Republic
2 Lublin University of Technology, Faculty of Mechanical Engineering, Nadbystrzycka 36, 20-618 Lublin, Poland

The paper is focused on the surface integrity in grinding of chromium-nickel steels. These steels are high alloy with an austenitic structure, which guarantees corrosion resistance in combination with high toughness and strength. They are used in various areas. The variety of their use also requires good properties in terms of technical processing. Most high-alloy chromium-nickel steels are well weldable and moldable, but their machinability is a problem, which was also experimentally monitored in the fine grinding process.

Keywords: Chromium-nickel steels, Grinding, Diffractometry

Published: October 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Stancekova D, Šajgalík M, Mrázik J, Rudawska A, Janota M. Analysis of Integrity of Surface of Hardened Chromium-Nickel Steel after Finishing Grinding. Manufacturing Technology. 2018;18(5):833-838. doi: 10.21062/ujep/186.2018/a/1213-2489/MT/18/5/833.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. NOVOTNÝ, J., LYSONKOVA, I., NAPRSTKOVA, N., MICHNA, S. (2017) Research of application possibilities of selected mechanically alloyed metal powders, In Manufacturing Technology, vol. 17, no. 5, p. 811-815. Go to original source...
    2. HRUBÝ, J., RENTKA, J., SCHINDLEROVÁ, V., KREJČÍ, L., ŠEVČÍKOVÁ, X. (2013) Possibilities of prediction of service life of forming tools. In Manufacturing Technology, vol. 12, no. 14, p. 178-181. Go to original source...
    3. KUZIČKIN, D., FREMUNT, P., MÍŠEK, B. (1988) Structural steel, wrought and on castings. Bratislava: Alfa, 304 p.
    4. SANDVIK COROMANT (2017) Training Handbook. Metal Cutting Technology. [Online, 31.1.2018] <http://sandvik.ecbook.se/se/en/training_hand_book/>
    5. VASILKO, K. a kol. (1990). New materials and technology for their processing. Bratislava: Alfa, 368 p.
    6. PETRŮ, J., SCHIFFNER, J., ZLÁMAL, T., ČEP, R., KRATOCHVÍL, J., STANČEKOVÁ, D. (2015) Wear Progress of Exchangeable Cutting Inserts During Ti6Al4V Alloy Machining. In METAL 2015 Conference Procedings of the 24Rd International Conference on Metallurgy and Materials.
    7. HANES, T., HVIZDOŠ, P., ŤAVODOVÁ, M., KALINCOVÁ, D., HRICOVÁ, J., BEŇO, P. (2014) Coating surface roughness measurement made on coining dies. In Manufacturing technology, vol. 14, no. 3, p. 309-317. Go to original source...
    8. SAPIETA, M; SAPIETOVA, A; DEKYS, V. (2017) Comparison of the thermoelastic phenomenon expressions in stainless steels during cyclic loading. In. METALURGIJA, vol. 56, Issue: 1-2, 2017, p. 203-206.
    9. NESLUSAN, M., BAMUROVA, J., MICIETOVA, A., CILLIKOVA, M. (2016) Performance of Norton Quantum Grinding Wheels. In Key Engineering Materials, Vol. 686, p. 125-130 Go to original source...
    10. CEP, R., JANASEK, A., PETRU, J., SADILEK, M., MOHYLA, P., VALICEK, J., HARNICAROVA, M., CZAN, A. Surface Roughness after Machining and Influence of Feed Rate on Process. In Key Engineering Materials, Vol. 581, pp. 341-347.
    11. DRBÚL, M., ŠAJGALÍK, M., ŠEMCER, J., CZÁNOVÁ, T., PETRKOVSKÁ, L., ČEPOVÁ, L. (2014) Engineering Metrology and the quality of surfaces created by machining technologies. Žilina: ŽU v Žiline, 115s.
    12. ČUBOŇOVÁ, N., KURIC. I. (2014) Data structures implementation of the protocol STEP-NC at CNC machines programming. In: Communications, vol. 16, no. 3A, pp. 176-183. Go to original source...
    13. VALÁŠEK, P., MÜLLER, M. (2015). Abrasive wear in three-phase waste based polymeric particle composites. In. Tehnicki Vjesnik-Technical Gazette, vol. 12, 2/2015, pp. 257-262. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content