Manufacturing Technology 2019, 19(6):959-965 | DOI: 10.21062/ujep/403.2019/a/1213-2489/MT/19/6/959

Design and Dynamic Performance Study on Hydrostatic Lubrication System of High-speed Precision Roller Grinding Head

Wu Huai-chao, Zhao Li-mei, Yan Wen-meng, Xu Lei
School of Mechanical Engineering, Guizhou University, Gui yang, 550025, China

To meet the need of high-speed steel roll grinding, a hydrostatic lubrication system for high-speed precision roller grinding head is designed and the dynamic performance of the system is simulated and analyzed in this study. The hydrostatic lubrication system was designed according to the lubrication characteristics of the eccentric sleeve and thrust bearing of the high-speed precision roller. Then the mathematical models of the main components of the system were established. And according to the schematic diagram of hydrostatic lubrication system, the dynamic performance of the lubrication system at high speed was simulated and tested. The simulation and experiment results show that the lubrication effect of the eccentric sleeve static chambers and thrust bearings is good, and the designed hydrostatic lubrication system is feasible.

Keywords: High-speed precision roller grinding head, AMESim, Lubrication system, Dynamic performance
Grants and funding:

National natural science foundation of China (Grant No.51465008), (Grant No. Q.R.X.M.Z.Z.H.T (2018)0001), (Grant No. Q.K.H.P.T.R.C[2017]5788), key research project on In-novation group in Guizhou Provincial Education De- 965 department (Grant No. Q.J.H. KY Z. [2018]011) and training plan for high-level innovative talent in Guizhou Province (Grant No. Q.K.H.P.T.R.C[2016] 5659).

Published: December 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Huai-chao W, Li-mei Z, Wen-meng Y, Lei X. Design and Dynamic Performance Study on Hydrostatic Lubrication System of High-speed Precision Roller Grinding Head. Manufacturing Technology. 2019;19(6):959-965. doi: 10.21062/ujep/403.2019/a/1213-2489/MT/19/6/959.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. WU, HUAICHAO,WANG KUNPENG, SUN GUANCHAO, ZHAO LIMEI. (2018). Influence study of oil film thrust bearing on thermal characteristics of high-speed precision roll grinding head. In: Manufacturing Technology, Vol. 18, No.2, pp. 330-336. Go to original source...
    2. GUO LI. (2000). Research on hydrostatic sliding bearing and its supporting Spindle system, ShanXi: Xi'an Jiao Tong University.
    3. HARINGOVÁ, ANDREA,STRACÁR, KAROL,PRIKKEL, KAROL. (2016). Application of lubrication into the hip joint replacement. In: Manufacturing Technology, Vol. 16, No.3, pp. 502-506. Go to original source...
    4. SATISH C. SHARMA; SATISH C. JAIN; R. SINHASAN; P. L. SAH. (2001). Static and dynamic performance characteristics of orifice compensated hydrostatic flexible journal bearings with non-Newtonian lubricants. In:Tribology Transactions, Vol. 44, No. 2, pp. 242-248. Go to original source...
    5. WU HUAICHAO, ZHAO LIMEI, NI SILIANG, HE YONGYONG. (2019). Study on friction performance and mechanism of slipper pair under different paired materials in high-pressure axial piston pump. In: Friction, https://doi.org/10.1007/s40544-019-0314-2. Go to original source...
    6. CHUN S M. (2003). Network analysis of an engine lubrication system. In:Tribology international, Vol. 36, No. 8, pp. 609-617. Go to original source...
    7. PEXA, M., ALEŠ, Z.,PAVLŮ, J.,ČEDÍK, J.,(2015). Impact of viscosity of motor oil on the wear of plain bearings. In: Manufacturing Technology, Vol. 15, No.4, pp. 670-674. Go to original source...
    8. CHUN S M, PARK Y H, JANG S. (2000). A Study on Engine Lubrication System by Optimized Network Analysis-Part I: Case Study. In: SAE Paper, 2000-01-2921. Go to original source...
    9. CHUN S M, PARK Y W. (2000). A Study on Engine Lubrication System By Optimized Network Analysis-Part II: Parametric Study. In: SAE Paper, 2000-01-2923. Go to original source...
    10. BENOIT HONEL, RENAUD MEILLIER, FREDERIC BRIX, et al. (2003). Model of an Engine Lubrication Circuit includingPredictive Bearing Components. In: SAE Paper, 2003-01-1965.
    11. LIU XUE-YUAN. (2007). Simulation and Experimental study on Lubrication system of D30 Diesel engine. YunNan: Kunming University of Science and Technology
    12. HUANGWEI-WEI. (2015). Simulation of Flow Characteristics on Lubricating System of a V type Multi-cylinder Diesel Engine. Beijing: Beijing Institute of Technology.
    13. Y FANG. (2012). Performance Study and Design of Hydrostatic Bearings on Roller Press. In: Lubrication Engineering, Vol. 37, No. 4, pp. 82-86.
    14. YADAV, SAURABH K.;SHARMA, SATISH C. (2014). Performance of hydrostatic tilted thrust pad bearings of various recess shapes operating with non-Newtonian lubricant. In: Finite Elements in Analysis and Design, Vol. 87, pp. 43-55. Go to original source...
    15. YU, XD; ZHANG, YQ; SHAO, JP, et al. (2009). Simulation Research on Gap Flow of Circular Cavity Multi-pad Hydrostatic Thrust Bearing. In: INTERNATIONAL CONFERENCE ON INTELLIGENT HUMAN-MACHINE SYSTEMS AND CYBERNETICS, Vol. 2, pp. 41.
    16. GOHARA M, SOMAYA K, MIYATAKE M, YOSHIMOTO S. (2014). Static characteristics of a water-lubricated hydrostatic thrust bearing using a membrane restrictor. In: Tribology International, Vol. 75, pp. 111-116. Go to original source...
    17. QIANLEI PENG, CHI ZHOU, LIANGJIN GUI, ZIJIE FAN. (2019). Investigation of the lubrication system in a vehicle axle: Numerical model and experimental validation. In: Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Vol. 233, No. 5, pp. 1232-1244. Go to original source...
    18. LIU JIAN. (2008). Research on Characteristic Analysis and Experiment of Pressure-limiting Variable Vane Pump. In: Journal of Mechanical Transmission, No. 3, pp. 86-88.
    19. JIN SHENG-QIU, CHENG KAI, WANG PENG-YU. (2009). Analysizing the Capability and Improving the Structure of Synchronization Valve Based on AMESim. In: Chinese Hydraulics & Pneumatic, No. 9, pp. 64-68.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content