Manufacturing Technology 2019, 19(6):1003-1009 | DOI: 10.21062/ujep/410.2019/a/1213-2489/MT/19/6/1003

Dynamic Analysis of the Crank Mechanism through the Numerical Solution

Marián Minárik, Ferdinand Bodnár
Department of Mechanics, Mechanical Engineering and Design, Faculty of Environmental and Manufacturing Technology, Technical University in Zvolen, ©tudentská 26, 960 01 Zvolen

Dynamic analysis of crank mechanism is realised by relaxation method, where a connecting rod is modelled with three manners. In the first case the connecting rod is modelled as a rigid body, in the second case this one is modelled with two mass points and in the third case the connecting rod is modelled with three mass points. Results of all manners of modelling are compared and evaluated.

Keywords: Crank Mechanism, Dynamic Analysis, Kinematic Quantities
Grants and funding:

Cultural and Educational Grant Agency the Ministry of Education, Science, Research and Sport of the Slovak Republic. „Progress and application of educational methods in the Mechanics of solids“ No. 015TU Z-4/2019.

Published: December 1, 2019  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Minárik M, Bodnár F. Dynamic Analysis of the Crank Mechanism through the Numerical Solution. Manufacturing Technology. 2019;19(6):1003-1009. doi: 10.21062/ujep/410.2019/a/1213-2489/MT/19/6/1003.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BODNÁR, F. (2008). Mechanika. Vydavateµstvo TU, Zvolen, ISBN 978-80-228-2016-5.
    2. GROS, D., HAUGER, W., SCHRÖDER, J., WALL, W. A., GOVINDJEE, S. (2014). Engineering Mechanics 3 - Dynamics. 2nd Edition, Springer, ISBN 978-3-642-53712-7. Go to original source...
    3. JANČINA, J., PEKÁREK, F. (1987). Kinematika. Alfa, Bratislava.
    4. LIAO, Y., LIAO, B. (2019). Dynamics Modeling and Modal Analysis of Machine Tool Considering Joints Parameters, Manufacturing Technology, Vol. 19, No. 2, pp. 267-272. (2019), ISSN 1213-2489. Go to original source...
    5. MINÁRIK, M. (2018). Experimentálne zistenie momentu zotrvačnosti ojnice. In: Podpora kvality vyučovacieho procesu v oblasti Mechaniky telies prostredníctvom rozvoja edukačných metód, vedecký recenzovaný zborník, Zvolen, 2018, s. 28-34. ISBN 978-80-228-3075-1.
    6. MINÁRIK, M., BODNÁR, F. (2018). Dynamická analýza centrického kµukového mechanizmu. In: Podpora kvality vyučovacieho procesu v oblasti Mechaniky telies prostredníctvom rozvoja edukačných metód, vedecký recenzovaný zborník, Zvolen, 2018, s. 35-51. ISBN 978-80-228-3075-1.
    7. SEGĄA, S., KAMPO, J., SOUKUP, J. (2019). Dynamic Analysis and Optimization of the Planar Model of the Trolleybus ©koda 21Tr, Manufacturing Technology, Vol. 19, No. 3, pp. 487-491. (2019), ISSN 1213-2489. Go to original source...
    8. VAVRO, J., VAVRO, J. jr., PECU©OVÁ, B., BURGET, M. (2018). Dynamic Analysis of Lever Mechanism for Manufacturing of Raw Tyres, Manufacturing Technology, Vol. 18, No. 1, pp. 145-148. (2018), ISSN 1213-2489. Go to original source...
    9. ZÁHOREC, O., CABAN, S. (2002). Dynamika. Edícia vedeckej a odbornej literatúry, Strojnícka fakulta TU, Koąice, ISBN 80-7099-825-3.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content