Manufacturing Technology 2020, 20(2):250-256 | DOI: 10.21062/mft.2020.025

Milling of Technical Ceramics ROCAR SiSiC

Dana Stancekova1, Jozef Mrázik1, Ingrid Görögová2, Izabela Miturska3, Peter ©čotka4, Filip Turian1
1 University of Zilina, Faculty of Mechanical Engineering, Zilina, Slovak Republic
2 Institute of Production Technologies, Slovak University of Technology in Bratislava, Slovakia
3 Lublin University of Technology, Faculty of Mechanical Engineering, Lublin, Poland
4 VIKO s.r.o, Povaľská Teplá 529, Slovak Republic

The paper deals with hard machining of ceramic construction materials that are still more applied in the automo-bile industry as well as other branches due to their specific properties, such as hardness, corrosion resistance, heat resistance, etc. Concretely, we speak of milling of technical ceramics ROCAR SiSiC. Our intention is the right se-lection of suitable tool materials, tool geometry as well as a definition of optimum cutting parameters by the min-imum cost. After the selection of optimum technology, identified cutting plates were compared and experimentally verified in the process. Results of verifications the right choice of selected cutting plate is a comparison of compo-nents of cutting force originating in the process of machining and also the quality of machined surfaces after mill-ing of hard and brittle material.

Keywords: Milling, Technical ceramics, Cutting forces, Surface quality
Grants and funding:

KEGA 011®U-4/2020.

Prepublished online: August 17, 2020; Published: August 18, 2020  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Stancekova D, Mrázik J, Görögová I, Miturska I, ©čotka P, Turian F. Milling of Technical Ceramics ROCAR SiSiC. Manufacturing Technology. 2020;20(2):250-256. doi: 10.21062/mft.2020.025.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. VASILKO, K. a kol. (2006). Top trendy v obrábaní III. čas» - Technológia obrábania. ®ilina: MEDIA/ST, 2006. 214 p. ISBN: 80-968954-2-7
    2. SEDLÁK, J., TROPP, P., CHLADIL, J., KOUŘIL, K. POLZER, A. OSIČKA, K. (2016). Analysis of Selected Aspects of Turned Bearing Rings Regarding Required Workpiece Quality. Manufacturing Technology, Vol. 2016, No.3, pp. 612-622. Go to original source...
    3. HUMÁR, A. (2008). Materiály pro řezné nástroje. MM publishing s.r.o., 235 s.
    4. http://www.ceramtec.cz/ceramic-materials/> [cit. 2013-10-21]
    5. NOVOTNÝ, J., LYSONKOVA, I., NAPRSTKOVA, N., MICHNA, S. (2017). Research of application possibilities of selected mechanically alloyed metal powders, In Manufacturing Technology, vol. 17, no. 5, pp. 811-815. DOI: 10.21062/ujep/x.2017/a/1213-2489/MT/17/5/81 Go to original source...
    6. PAGÁČ, M., MALOTOVÁ, ©., SADÍLEK, M., PETRŮ, J., ZLÁMAL, T., KRATOCHVÍL, J. (2016). Influence of effective milling strategies on the residual stress. In. METAL 2016, Conference Proceedings 2016, pp. 819-824
    7. MONKOVA, K., SUN, S., MONKA, P.P., HLOCH, S., BELAN, M. (2020) Durability and tool wear investigation of HSSE-PM milling cutters within long-term tests. In. Engineering Failure Analysis, Vol. 108, Art. Num. 104348 Go to original source...
    8. KUCZMASZEWSKI, J., ZAGORSKI, I., GZIUT, O., LEGUTKO, S., KROLCZYK, G.M. (2017). Chip fragmentation in the milling of AZ91HP magnesium alloy. In. Strojniski Vestnik/Journal of Mechanical Engineering. Vol. 63, Issue 11, 2017, pp. 628-642 Go to original source...
    9. MAREK, M., NOVÁK, M., ©RAMHAUSER, K., SVOBODOVÁ, J. (2018) Analysis of the base material and Hard chrome plated layer in an unloaded state. Manufacturing Technology, 18(4), pp. 616-620 Go to original source...
    10. ČUBOŇOVÁ, N., KURIC. I. (2014) Data structures implementation of the protocol STEP-NC at CNC machines programming. In: Communications, vol. 16, no. 3A, pp. 176-183. Go to original source...
    11. BOTKO, F., HATALA, M., KORMO©, M., UNGUREANU, N., & ©OLTÉS, P. (2015). Using Edgecam for creating CNC programs in education process. In 2015 IEEE 13th International Symposium on Applied Machine Intelligence and Informatics (SAMI) (pp. 255-259). IEEE. Go to original source...
    12. KALINCOVÁ, D., «AVODOVÁ, M., JAKUBÉCZYOVÁ, D. (2018) Quality evaluation of the coatings and its influence on the wood machining tool wear. Manufacturing Technology, 18(4), pp. 578-584 Go to original source...
    13. NOVÁ, I., FRAŇA, K., MACHUTA, J., NOVÁKOVÁ, I. (2019) Theoretical calculations of the foaming properties of powder agents for the production of Aluminium foams. Manufacturing Technology, 19(1), pp. 118-122 Go to original source...
    14. ČEP, R. PETRU, J., ZLÁMAL, T., VALÍČEK, J., HARNIČÁROVÁ, M., JANÁSEK, A., ČEPOVÁ, L. (2013) Influence of Feed Speed on Machined Surface Quality, In. METAL 2013, pp.1033-1038.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content