Manufacturing Technology 2021, 21(6):842-848 | DOI: 10.21062/mft.2021.087
Elimination of resonant phenomena adverse effect in the process of experimental operation of gears
- Technical University of Koąice. Faculty of Manufacturing Technology, 080 01 Preąov, Bayerova 1, Slovak Republic
The paper describes the course, conditions and results of the impact test of the supporting frame of the test station for dynamic tests of gears. The test station makes it possible to simulate different gears operating conditions. The basic support frame structure of the test station was evalu-ated as unsufficient based on the results of measurement and processing of the measured low and high fre-quency vibration values in the verification series of experimental tests. The basic failure of the origi-nal design were the significant resonance actions that were the results of the dominant sources of vibration being near the natural frequencies of the vertical and horizontal beams of the test station base. A structural design of the test station supporting frame was designed and implemented. The goal was to increase the rigidity of the frame and eliminate unwanted resonance phenomena. The impact tests were used to determine the values of the natural frequencies of the most stressed parts of the supporting structure - vertical and horizontal beams, before and after implementation of struc-tural modifications. The comparability of the impact test results was determined by adherence to identical measurement conditions.
Keywords: Test Station, Dynamic Tests, Gears, Natural Frequencies, Impact Test
Grants and funding:
This work was supported by the Slovak Research and Development Agency under contract no. APVV-18-0316.
Received: July 13, 2021; Revised: November 21, 2021; Accepted: December 1, 2021; Prepublished online: December 26, 2021; Published: January 8, 2022 Show citation
References
- ©MERINGAIOVÁ, A., VOJTKO, I., MONKOVÁ, K. (2015). Experimentelle Analyse der Dynamik von Zahnradgetrieben - Teil 1. tm-Technisches Messen, Vol. 82, No. 2, pp. 57 - 64.
Go to original source...
- PAVLENKO, S., MA©ČENÍK, J., KRENICKÝ, T. (2018). Worm gears: general information, calcula-tions, dynamics and reliability, p. 167. Lüdenscheid: RAM-Verlag. ISBN 978-3942303804
- ©MERINGAIOVÁ, A., VOJTKO, I., MONKOVÁ, K. (2015). Experimentelle Analyse der Dynamik von Zahnradgetrieben - Teil 2. In: tm-Technisches Messen, Vol. 82, No. 4, pp. 224 - 232.
Go to original source...
- ISO 10816-3:2009 Mechanical vibration. Evaluation of machine vibration by measurements on non-rotating parts - part 3
- MURČINKOVÁ, Z., MURČINKO, J., ADAMČÍK. P. (2016). The multi-parameter on-line monitoring system applied for rotating machinery. In: Review of Industrial Engineering Letters, Vol. 3, No. 2, pp. 19-28.
Go to original source...
- OLEJÁROVÁ, ©., RU®BARSKÝ, J., KRENICKÝ, T. (2019). Vibrations in the Production: Sys-tem Measurement and Analysis with Water Jet Technology. 1rd ed. Cham: Springer Nature Switzerland.
Go to original source...
- ®IARAN, S. (2016). Low frequency noise and vibration (Nízkofrekvenčný hluk a kmitanie), p. 316. STU Bratislava. ISBN 9788022745369
- ZÁHOREC, O., CABAN, S. (2002). Dynamics (Dynamika), p. 500. SjF TUKE Koąice. ISBN 80-7099-825-3
- ÇAKAR, O. (2018). A method for shifting natural frequencies of a dynamic system to desired values with concentrated mass modifications. In: Journal of Vibroengineering, Vol. 20, No. 1, pp. 1- 12.
Go to original source...
- KALIŃSKI, K. J. et al. (2019). Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping. In: Applicable Solutions in Non-Linear Dynamical Systems: Proceedings of the DSTA 2019, pp. 249-58. ŁódĽ: Politechnika Łódzska.
- KLIMENDA, F., SOUKUP, J., STERBA, J. (2019). Noise and Vibration Analysis of Conveyor Belt. In: Manufacturing Technology, Vol. 19, No. 4, pp. 604-608. Elsevier. Netherlands.
Go to original source...
- LIU, SY. et al. (2019) Investigation on the influence of work holding equipment errors on contact charac-teristics of face-hobbed hypoid gear. In: Mechanism and Machine Theory, Vol. 138, pp. 95-111.
Go to original source...
- MO S., ZHANG T. (2020). Analytical Investigation on Load Sharing Characteristics of Herringbone Planetary Gear Train with Flexible Support and Floating Sun Gear. In: Mechanism and Machine Theory, Vol. 144, No. 2, pp. 1-27.
Go to original source...
- VA©INA M., HRU®ÍK L., BUREČEK A. (2020). Study of Factors Affecting Vibration Damping Prop-erties of Multilayer Composite Structures. In: Manufacturing Technology, Vol. 20, No. 1, pp. 104-109.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.